SP Shocker CVO Owner's Manual
  1. Manuals
  2. Brands
  3. SP Manuals
  4. Paintball equipment
  5. Shocker CVO
  6. Owner's manual

SP Shocker CVO Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

SHOCKER
CVO
PLEASE READ CAREFULLY
OWNER'S MANUAL
1
WWW.SHOCKERPAINTBALL.COM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Shocker CVO and is the answer not in the manual?

Questions and answers

Related Manuals for SP Shocker CVO

Summary of Contents for SP Shocker CVO

  • Page 1 SHOCKER PLEASE READ CAREFULLY OWNER’S MANUAL WWW.SHOCKERPAINTBALL.COM...

  • Page 2: Quick Start

    PARTS GUIDE it on. While wearing ASTM compliant paintball goggles in an area where all bystanders are protected, remove the – SP RECOMMENDS THAT THE SHOCKER ® barrel blocker and fire over a chronograph to measure the velocity. Using a 5/32-inch hex key, turn velocity up WARRANTY (clockwise) or down (counter-clockwise) as needed to meet the field’s standard.

  • Page 3: Trigger Adjustment

    The Shocker CVO is factory- pre-travel screw. loader from the Shocker ®...
  • Page 4 LOAD E R / F EED NECK PLEASE READ CAREFULLY PLEASE READ CAREFULLY QEV ADJUSTMENT Bolt closing force has a significant impact LOADER It is highly recommended that the Shocker® CVO be LOADER BOLT FORCE ADJUSTMENT paired with a force-feed loader to obtain best performance on on how a paintball marker fires, both in terms of the marker’s the field [Fig 09].
  • Page 5 BO LT C LE ANING D ET EN TS PLEASE READ CAREFULLY PLEASE READ CAREFULLY The Shocker CVO utilizes a spool valve design which combines ® DETENTS The ball detents in the Shocker CVO prevent double- ® RELEASE LATCH RELEASE LATCH its bolt with its main exhaust valve for a system that uses few feeding and subsequent chopping of paintballs by preventing parts for efficient performance with few possible failure points.
  • Page 6 A SA RE GU L ATOR PLEASE READ CAREFULLY PLEASE READ CAREFULLY ASA KNOB The ASA Knob may occasionally need to be removed Removal of the regulator’s internal components is an advanced SPRING PLATFORM ASA KNOB for cleaning or lubrication, especially if the Shocker ®...
  • Page 7 REGULATOR PISTON Reach inside with an o-ring pick or operation. When testing the Shocker CVO after performing needle nose pliers and pull the piston out by its spring to pull the regulator maintenance, always wear paintball eye and face regulator piston out [FIG.
  • Page 8 GR IP F RA M E TR I GGER PLEASE READ CAREFULLY PLEASE READ CAREFULLY Removal of the grip frame is an advanced maintenance TRIGGER The Shocker CVO pivots on a pair of bearing sets ® GRIP FRAME TRIGGER procedure that should only be performed when needed to repair nested onto a low friction pin.

  • Page 9: Pilot Valv E

    PILOT VALV E B O LT C ONT ROL PLEASE READ CAREFULLY PLEASE READ CAREFULLY PILOT VALVE Disassembly of the pilot valve should only be BOLT CONTROL MANIFOLD The bolt control manifold [FIG. REASSEMBLY Before reassembly, lubricate o-rings very PILOT VALVE O-RING performed when necessary for repair.
  • Page 10 T ROU BL E SHOOT IN G T R OU B L ESH O OT I N G PLEASE READ CAREFULLY PLEASE READ CAREFULLY WHEN GASSED UP, THE BOLT IMMEDIATELY CLOSES. WHEN GASSED UP AIR LEAKS FROM BETWEEN THE GRIP GRIP FRAME WILL NOT FIT CORRECTLY TO BODY.
  • Page 11 PA RTS G U IDE PA RTS GU I D E PLEASE READ CAREFULLY PLEASE READ CAREFULLY FIRING CAN CHAMBER GUIDE OM7020 (3x) OB7017 APPLY GR33SE™ LIGHTLY SHK110 OB7M06 (18x3mm) APPLY GR33SE™ LIGHTLY OM7014 SHK208 DOW33 GREASE APPLY GR33SE™ LIGHTLY OM7017 APPLY GR33SE™...
  • Page 12 PA RTS G U IDE PA RTS GU I D E PLEASE READ CAREFULLY PLEASE READ CAREFULLY MAIN CHAMBER BOLT SHK110 OB7017 OM7014 SHK256 OM7017 OM7010 APPLY GR33SE™ (2x) SHK205 OM7017 SHK208 BUM004 OM7015 OM7010 (2x) APPLY GR33SE™ OM7015 LIGHTLY APPLY GR33SE™ OU7013 TO SURFACE SHK103...
  • Page 13 PA RTS G U IDE PA RTS GU I D E PLEASE READ CAREFULLY PLEASE READ CAREFULLY VALVE MANIFOLD BOLT CONTROL MANIFOLD OB7008 - AS008 buna 70 durometer OB7M04 - 3mm x 1mm buna 70 durometer OU7003 - AS003 urethane 70 durometer USE ORING TOOL (FXT030) TO SLIDE OB7M04 ONTO XTC122 3MM x 1MM 003 OB7013 - AS013 buna 70 durometer...
  • Page 14 (3 x 1MM) PIN012 OB7M25 SHK102 (.76 x 3.48MM) SOS005 (2x) SHK224 OM9M01 (4 x 1MM) NO O-RING INSTALLED OB7018 WHEN USED FOR SHOCKER CVO OB7008 OB7M04 (3 x 1MM) STK016 QEV105 OB7018 FRKBXL02 SHK125 SHK239 AAMFXL09 OB7M04 (3 x 1MM) SHOCKER WWW.SHOCKERPAINTBALL.COM...
  • Page 15 PA RTS G U IDE PA RTS GU I D E PLEASE READ CAREFULLY PLEASE READ CAREFULLY LATCH ASSEMBLY DETENT COVER PIN011 SHK220 SHK122 SPR017 (2x) SHK242 SPR036 SHK121 OB7M01 (1 x 1MM) SHK111 PIN013 (2x) DO NOT GREASE! SHK312 (LEFT) SSS014 (2x) SHK313 (RIGHT) (BLUE LOCTITE 242)
  • Page 16 PA RTS G U IDE PA RTS GU I D E PLEASE READ CAREFULLY PLEASE READ CAREFULLY CLAMPING FEEDNECK REGULATOR PISTON VRG106 SHK133 OM7014 APPLY GR33SE™ VRG205 QLK205 QLK206 INSTALL VRG106 INTO VRG105 ENSURE IT IS INSTALLED FLAT INSTAL VRGI06 INTO VRG 10 ENSURE IS INSTA LLED FLAT AND SITS AND SITS SLIGHTLY ABOVE THE...
  • Page 17 PA RTS G U IDE PA RTS GU I D E PLEASE READ CAREFULLY PLEASE READ CAREFULLY SPRING GUIDE REGULATOR BASE OB7012 OB7014 OM7010 APPLY GR33SE™ APPLY GR33SE™ OM7006 OB7010 APPLY GR33SE™ OU7010 APPLY GR33SE™ SHK226 SHK128 SHOCKER WWW.SHOCKERPAINTBALL.COM...
  • Page 18 PA RTS G U IDE PA RTS GU I D E PLEASE READ CAREFULLY PLEASE READ CAREFULLY SPRING PLATFORM BASE REGULATOR SPRINGS SHK128 OB7012 OU7010 OB7010 SHK226 OM7006 OB7014 SHK130 OB7014 OM7010 SHK129 VRG107 SPR032 SPR035 VRG106 OM7012 SHK129 SHK127 VRG205 OM7014 OB7014...
  • Page 19 PA RTS G U IDE PA RTS GU I D E PLEASE READ CAREFULLY PLEASE READ CAREFULLY BOTTOM LINE ASA TRIGGER BRG002 SHM236 SOS016 SHK138 SHM207 SHK237 OU9005 SSS017 (DOW33 GREASE) BRG002 OB7010 (ON KNOB BEHIND THREAD) SHOCKER WWW.SHOCKERPAINTBALL.COM...

  • Page 20: Warranty

    PA RTS G U IDE WARRAN T Y PLEASE READ CAREFULLY PLEASE READ CAREFULLY 4 buna 70 durometer SSS018 - 6-32 x .500 socket set screw stainless 4 urethane 70 durometer SSB009 - 6-32 x .250 socket button head stainless Shocker Paintball warrants to initial retail purchaser that the 3 urethane 90 durometer PIN025 - .094 diameter x .500 length acetal pin...

  • Page 21: Please Read Carefully

    PLEASE READ CAREFULLY WWW.SHOCKERPAINTBALL.COM 100 STATION ST. | LOYALHANNA, PA 15661 | (724) 520-8690 MANUAL VERSION 1.0 Shocker and Freak are registered trademarks owned by G.I. Sportz, Inc. and used under license by Philadelphia Americans, LLC. ® ® SHOCKER CVO™ and XLS™ are trademarks owned by Philadelphia Americans, LLC. Trademarked loader names are the properties of their respective owners which are not affiliated with Shocker Paintball.

Table of Contents