Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Datavan Facelook X1
- Page 1 User’s Manual Version:4.6...
- Page 2 Facelook X1 User’s Manual MPORTANT AFETY NFORMATION This section presents important information intended to ensure safe and effective use of this product. Read this section carefully and store it in an accessible location. AFETY RECAUTIONS When the device cannot be exited or terminated, reset and restart it by powering off and on again.
-
Page 3: Table Of Contents
Facelook X1 User’s Manual ONTENTS 1. OVERVIEW 1.1 INTRODUCTION 1.2 PACKING LIST 1.3 APPEARANCE AND COMPONENTS 1.3.1 APPEARANCE 1.3.2 DIMENSION 1.3.3 CONNECTORS 2. INSTALLATION AND OPERATION 2.1 WALL-MOUNT INSTALLATION 2.1.1 INSTALLATION AND FIXING 2.2 CONNECTING NETWORK 2.2.1 CONNECT TO PC DIRECTLY 2.2.2 CONNECT BY LAN... -
Page 4: Overview
VERVIEW 1.1 I NTRODUCTION Facelook X1 is a facial recognition and body temperature detection device which is capable of detecting temperature abnormity without actual physical contact at different application fields. It alerts when abnormal body temperature and recognizes face while wearing or without wearing a mask. -
Page 5: Appearance And Components
Facelook X1 User’s Manual 1.3 A PPEARANCE AND OMPONENTS 1.3.1 A PPEARANCE Dimension: 252(L)*136(W)*26(H)mm(8 inches) Weight: 1.7KG 1.3.2 D IMENSION 5 / 24... -
Page 6: Connectors
Facelook X1 User’s Manual 1.3.3 C ONNECTORS Name Description Label Network port RJ45 ① Power supply DC12V IN DC12V IN ② (Reserved) ③ Switch Output A+/B- KZ_OUT ④ Wiegand IN (Reserved) WG IN ⑤ Wiegand OUT (Reserved) WG OUT ⑥... -
Page 7: Installation And Operation
Facelook X1 User’s Manual 2. I NSTALLATION AND PERATION 2.1 W ALL- OUNT NSTALLATION 2.1.1 I NSTALLATION IXING Release the 2 screws and take out the wall bracket from device. Check the installation height of the face recognition monitor. It is recommended to fix the bracket on the wall about 1.5m height. -
Page 8: Connecting Network
Facelook X1 User’s Manual 2.2 C ONNECTING ETWORK To configure the device, connect PC to device. Two ways can be used to connect the device and PC. Select either one of the ways. 2.2.1 C PC D ONNECT IRECTLY Connect device and PC with a network cable through RJ-45 port. -
Page 9: Connect By Lan
Facelook X1 User’s Manual Select [Use the following IP address]. Fill [IP address] and [Subnet mask]. 2.2.2 C ONNECT BY The IP address on device is set at DHCP which automatically obtains an IP address from LAN (Local Area Network). Simply connect both device and PC on LAN. -
Page 10: Web Configuration
Facelook X1 User’s Manual 2.3 W ONFIGURATION 2.3.1 L OGIN EVICE On PC, open web browser to login the device. It is recommended to use Google Chrome. Input the default IP address, 192.168.2.10, or the IP obtained from LAN, in URL column. -
Page 11: View Device Information
Facelook X1 User’s Manual 2.3.2 V EVICE NFORMATION The device information page shows the device software version and mac address. 2.3.3 P ERSONNEL ANAGEMENT 1. Person Registration Register the face image in device. Select photo, input name, employee number, phone number, ID card and remark1~4. Select the permanent authorization, and click [OK] to register. - Page 12 Facelook X1 User’s Manual 2. File Import In order to duplicate personnel database from another device, import the personnel database file that exported from the main device. Click [Upload File] to select the database file. Click [OK] to upload. The file to be imported should be original file exported from device.
- Page 13 Facelook X1 User’s Manual 4. Personnel Query The registered persons are listed in this page. Query the person according to the employee number, name or registered date by the option column. Click edit icon to revise the personnel information. Click delete icon to delete this person.
-
Page 14: Equipment Management
Facelook X1 User’s Manual 2.3.4 E QUIPMENT ANAGEMENT 1. Detection Management This page is to configure detection settings. It is divided into four parts: identification settings, temperature settings, and mask settings. Set the settings depending on the requirements. Identification Settings Identity Verification: Select to enable facial recognition to verify registered persons. - Page 15 Facelook X1 User’s Manual Site Map Configuration Passing Site Map: The default is enabled. If set at disable, the individual’s pictures will not be saved in access record when recognizing face. Temp. Detection Settings Temp. Mode: Depend on the environment, set the detection sensitivity as [Outdoor], [Indoor] or [Customize].
- Page 16 Facelook X1 User’s Manual 3. Customize This page is to upload logo and calibrate temperature. Logo Setting This is to upload the device identification logo at the lower-left corner of display. The default does not show a logo. Select [Customize] and choose a logo file to upload logo file.
-
Page 17: Access Control Settings
Facelook X1 User’s Manual 2.3.5 A CCESS ONTROL ETTINGS When the person is verified, the device sends signal to trigger gate to open. The trigger signal can be configured depending on the requirements. Unlock Length: The signal lasting time for open. -
Page 18: System Management
Facelook X1 User’s Manual 2.3.7 S YSTEM ANAGEMENT Manually restart the device, restore factory settings, and upgrade firmware. [Restart]: Reboot the device. [Factory Default]: Return to factory default. All the settings and data will be reset. [Clear Data]: Clear all registered face database and access record. -
Page 19: Specification
Facelook X1 User’s Manual 3. S PECIFICATION 3.1 P RODUCT EATURES Capable of trace of the movement of a human face in dim lit environment Patented facial recognition algorithm, capable to recognize faces with high accuracy, response time＜0.5s ... -
Page 20: Technical Specifications
Facelook X1 User’s Manual 3.2 T ECHNICAL PECIFICATIONS 3.2.1 T EMPERATURE ETECT PECIFICATIONS Item Specification Operating Temperature 15℃~35℃ (In door) Temperature detection range 30℃～45℃ Variation Range ±0.3℃ Detecting Distance 35~50cm (Horizontal) Abnormal Exceed 37.3℃ forehead temperature Warning 20~30 mins device warm up is recommended before use... -
Page 21: Camera Specifications
Facelook X1 User’s Manual 3.2.3 C AMERA PECIFICATIONS Item Specification Camera Binocular camera, Visible and near infrared 2.1M Pixels, 1920*1080 Effective MegaPixels Minimum multicolor 0.01Lux @F1.2(ICR); Black and white 0.001Lux @F1.2 Illumination (ICR) ≥50db(AGC OFF) Signal to Noise Ratio Wide Dynamic 120db，ISP algorithm face partial exposure... -
Page 22: Hardware Specifications
Facelook X1 User’s Manual 3.2.5 H ARDWARE PECIFICATIONS Item Specification Processor Dual-core processor+1G RAM +16G Flash Linux Image Sensor 1/2.8" Progressive Scan CMOS Speaker Standard and pre-recorded contents Operating Indoor recommended Temperate 0～90% RH Contact ±6KV, Air ±8KV Anti-static Power... -
Page 23: Faq
Facelook X1 User’s Manual 4. FAQ Q1. What happens in case the memory for access record is full? The oldest records will be overwritten by new records. The memory keeps working. Q2. When open web browser to login device, no response from device. -
Page 24: Appendix Agate Principle And Connection
Facelook X1 User’s Manual APPENDIX A G RINCIPLE AND ONNECTION On the gate, there is supposed to be a pair of trigger wires for triggering the gate to open. There are 2 states for wires: ● Wire Seperated, Gate Closed ●...