Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for RHINO METALS PSIW2418
Summary of Contents for RHINO METALS PSIW2418
- Page 1 ® SAFE OWNER’S MANUAL MODEL NO. PSIW2418 SERIAL NO. ___________________________...
-
Page 2: Sales Receipt/Letter From The Company
ATTACH COPY OF ORIGINAL SALES RECEIPT HERE At Rhino Metals, Inc., our job goes beyond just making safes. We believe our ultimate responsibility is to provide a quality product that creates peace of mind and unmatched value for our customers. -
Page 3: Safe Information
Serial Number: ___________________________________________ Combination: ___________________________________________ Purchased From: ___________________________________________ Date: ___________________________________________ Rhino Metals, Inc. Makers of Rhino and Bighorn Safes 607 Garber Street Caldwell, ID 83605 208-454-5545 208-459-0819 (FAX) www.rhinosafe.com Toll Free: 800-701-9128 For Technical Support issues, it is helpful to be near your safe when you call. -
Page 4: Table Of Contents
Contents Sales Receipt/Letter from the Company Safe Information Contents Getting Started—Manual Lock Getting Started—Electric Lock Electric Lock Operation 7- 8 Bolting Down your Rhino Safe Frequently Asked Questions Troubleshooting Guide 10 –11 Warranty... -
Page 5: Getting Started-Manual Lock
Getting Started—Manual Lock NEVER SPIN THE DIAL, TURN SLOWLY USE THE OPENING INDEX MARK LOCATED AT THE 12 O’CLOCK POSITION ON THE OUTER RING OF LOCK OPENING Turn dial left (counter-clockwise) at least four full revolutions stopping exactly on the first number of your combination (see front cover for combination). -
Page 6: Getting Started-Electric Lock
Getting Started—Electric Lock BATTERY INSTALLATION This applies to SecuRam and LaGard electronic locks only. 9 volt Battery required (not included). Use a new battery with “use date” at least 4 years in the future. Pre-used or old batteries will likely cause your lock to malfunction. -
Page 7: Electric Lock Operation
Electric Lock Operation LaGard Lock SecuRam Lock OPENING THE LOCK Enter the existing six digit code. The lock comes from the factory set to 1-2-3-4-5-6 and/or 1-1-1-1-1-1. Each key press is confirmed with an audio and light signal. The lock will indicate a valid code entry with a double signal. - Page 8 Electric Lock Operation CHANGING YOUR BATTERY Slide the keypad housing up and carefully pull away from mounting surface to expose battery compartment. Remove 9-Volt battery and replace with a new one with “use date” at least 4 years in the future.
-
Page 9: Bolting Down Your Rhino Safe
Bolting Down Your Rhino Safe Your safe is predrilled from the factory for anchoring, with 2 holes in the bottom of the safe. 1. Anchoring hardware is not included. Purchase anchor bolts correctly suited for your floor type. We recommend using wedge anchor bolts 3” or longer for concrete floors and 1/2”... -
Page 10: Frequently Asked Questions
FREQUENTLY ASKED QUESTIONS Where is my serial number located? Your serial number is located on the back of the safe and also on the inside of the door, visible only when the doorback is removed. This manual also has the serial number on the cover. - Page 11 I am getting no response from my electronic lock. Replace your battery with a new 9V Duracell™ or Energizer™ battery with a “use date” of at least 4 years in the future. Low current will cause keypad to malfunction. Make sure all wires are properly and tightly connected to the keypad with no pinched wires or bent connectors.
-
Page 12: Warranty
Limited Warranty Rhino Metals, Inc. (the “Company”) warrants to the original consumer (the ”Purchaser”) that the Ironworks PSIW2418 safe (the “Safe”) will be free from defects in workmanship and materials for a period of one (1) year from the date of purchase.
Need help?
Do you have a question about the PSIW2418 and is the answer not in the manual?
Questions and answers