Subscribe to Our Youtube Channel
Summary of Contents for Royal Enfield M2d
- Page 1 Proportional Pneumatic Control Valve with integrated Driver Product Manual Page 1 of 15 Proportional Pneumatic Control Valve with Integrated Driver Product Manual...
-
Page 2: Table Of Contents
Proportional Pneumatic Control Valve with integrated Driver Product Manual Page 2 of 15 Contents Warnings & Notices _____________________________________________________________ 3 Overview _____________________________________________________________________ 4 Typical Applications _____________________________________________________________ 5 Product Layout_________________________________________________________________ 6 Product Specifications ___________________________________________________________ 7 System Requirements____________________________________________________________ 7 Components _______________________________________________________________________ 8 Tools _____________________________________________________________________________ 8 Configuration _______________________________________________________________________ 8 Implementation Instructions _______________________________________________________ 9 Receipt Inspection &... -
Page 3: Warnings & Notices
While the product is low voltage, it is an open-frame electronic component and care should be taken to prevent un- intentional contact with the product to avoid damage to person or property. The M2d is an electro-static sensitive device. Use appropriate electro-static discharge (ESD) procedures during handling and installation. -
Page 4: Overview
The aperture of the M2d is controlled at very high speed, allowing the valve to respond quickly to set-point command changes. When at a given set-point, the aperture is held steady rather than pulsing to create an average flow from a duty cycle. -
Page 5: Typical Applications
Proportional Pneumatic Control Valve with integrated Driver Product Manual Page 5 of 15 Typical Applications There are numerous applications and configurations for the M2d. Below are a chart of generic application descriptions and three common applications in pneumatics. Control Objective Technology Control Scheme ... -
Page 6: Product Layout
Proportional Pneumatic Control Valve with integrated Driver Product Manual Page 6 of 15 Product Layout Top View Photo Bottom View Photo... -
Page 7: Product Specifications
Proportional Pneumatic Control Valve with integrated Driver Product Manual Page 7 of 15 Product Specifications Specification Value Physical Characteristics SI Units Imperial Units Mass (Weight) 0,852 kg (30.0 oz) Approximate Physical Dimensions (L x W x H) 171.9 mm x 55.0 mm x 45.0 mm 6.77”... -
Page 8: Components
Proportional Pneumatic Control Valve with integrated Driver Product Manual Page 8 of 15 The following components are minimally required to implement a system. Refer to the Product Specifications and Configuration Instructions for details. Components Component Notes Recommendations & Sources 24V DC, 30W power Power supply to convert AC line voltage to Enfield Technologies A-PWR-BS-24V-36W supply... -
Page 9: Implementation Instructions
Page 9 of 15 Implementation Instructions The M2d can be used in many applications. Accordingly, it can be configured in many ways. These configuration instructions cover standard open-loop and closed-loop implementations as well as some advanced variations. The concepts of open-loop versus closed-loop systems, are important to implementing this or any pneumatic control system. -
Page 10: Receipt Inspection & Handling
Ensure that the M2d is properly connected to the master controller on startup to ensure proper valve operation Ensure that the target apparatus is properly connected to the M2d on startup to ensure proper operation ... -
Page 11: Wiring External Connections (Using Cbl-001 And Cbl-003)
(CMD-) command signal input (-), connect to the master controller command signal output (or connect directly to AGND for 0...5…10 Vdc command signals) (AUX1+) functionality not supported by the M2d (AUX1-) functionality not supported by the M2d ... -
Page 12: Led Indicators
Shared Power Supply: Enfield Technologies recommends that if a common power supply is used for both the M2d and the feedback sensor, that it should have a separately regulated power supply connections for the valve and the sensor. LED Indicators The M2d is equipped with three LED indicators: ... -
Page 13: Configuration Of Command Signal Via Dip Switch Settings
#1 and #2 in the OFF position #2 and #8 in the ON position The M2d does not require periodic factory calibration, but periodic tuning of the control system may be required due In this view #2 is on the left,... -
Page 14: Configuring And Tuning For Closed-Loop Control
Proportional Pneumatic Control Valve with integrated Driver Product Manual Page 14 of 15 Decommissioning & Corrective Maintenance The device is not serviceable in the field. If corrective maintenance is required, contact the manufacturer for return authorization at +1 203 375 3100 (+1 800 504 3334 toll free in North America) or via email at info@enfieldtech.com. -
Page 15: Product Warranty
Proportional Pneumatic Control Valve with integrated Driver Product Manual Page 15 of 15 Product Warranty This product is covered by Enfield Technologies’ standard 1-year Limited Warranty. The terms of the Limited Warranty are subject to change. The Limited Warranty is available online at www.enfieldtech.com or by request (see contact information below).
Need help?
Do you have a question about the M2d and is the answer not in the manual?
Questions and answers