Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Edmund Bühler TH 15
- Page 1 TH 15 Operating Instructions Bühler Incubator Hoods TH 30...
-
Page 2: Table Of Contents
3.2 Fixation of the incubator hood on a shaker ........... 5 4.0 Operation of the Models ................6 4.1 Operating Panel TH 15................6 4.2 Operating Panel TH 30................7 4.3 Safety Cut-off when the Incubator Hood is Opened ....... 8 5.0 Maintenance and Servicing Instructions ............ -
Page 3: General Notes
General Notes Thank you for choosing a Bühler product for supporting you in your work. The Bühler incubator hoods were developed for the use in laboratories in neutral atmospheres. If you pay attention to the following points, the device will reward you with long life and optimal operation. -
Page 4: General Notes Concerning Areas Of Application And Mode Of Operation
• Production of secondary natural substances and biogenous pharmaceutics The Bühler incubator hoods can be used as independent incubator chambers. Combined with Bühler shakers they are complete incubator shakers. Corresponding Bühler Shakers: with TH 15: with TH 30: Model KS 15 A control Model SM 30 A control Order No. -
Page 5: Transportation Instructions
2.0 Transportation Instructions Safe transportation of the devices is only ensured if original packaging is used. If they are bumped hard or put down roughly, damages can occur. ATTENTION: Do not lift the device at the handle ! Transport the device by holding it at the housing (bottom) only! 3.0 Installation and Connection 3.1 As independent constant temperature chamber:... -
Page 6: Operation Of The Models
The combination of a shaker type KS 15 with universal tray for spring clamps and incubator hood TH 15 may require higher distance rings between shaker and tray, otherwise the tray could be blocked. Please contact us if this is the case. -
Page 7: Operating Panel Th 30
4.2 Operating Panel TH 30: - UV TH 30 Key/ Function Display Mains switch ON/OFF Control lamps + Key (set value) - Key (set value) Function key Function key Display Light ON/OFF UV light ON/OFF • The incubator hood is switched on (I) or off (0) by means of the mains switch. (After having switched the mains switch on, the temperature control runs a self test which lasts approx. -
Page 8: Safety Cut-Off When The Incubator Hood Is Opened
At the incubator hood TH 30 2 additional pairs of keys serve for switching light (8) or UV light (9) on or off. 4.3 Safety Cut-off when the Incubator Hood is Opened When the incubator hood is used as incubator shaker in combination with a shaker, the shaker is automatically stopped for reasons of safety when the hood is opened. -
Page 9: Exchange Of The Fuse
5.1 Exchange of the Fuse The device is protected against overload by means of a fine fuse (see technical data). The fuse holder is located at the back of the device underneath the mains plug. Pull out the fuse insert and exchange the fuse. ATTENTION: Before removal of the fuse insert disconnect the mains plug ! 5.2 Overheat Protection... -
Page 10: Technical Data
• Extended temperature range up to 60°C Order No. 0052 105 Can be delivered for TH 15 and TH 30, but should be indicated in case of order. Retrofitting of this option is only possible in our works. • Cooling coil (TH 30 only !) Order No. -
Page 11: Accessories For Th 30
Accessories for TH 30: 2-storey top frame SM/TH: Thanks to the newly developed 2-storey top frame SM/TH the capacity of the incubator hood TH 30 can be even better utilized. The top frame fits on all shakers type SM and can be used in combination with the incubator hood TH 30. It allows shaking and incubation of small or shallow vessels (maximum height approx. - Page 12 Space Requirement of SM 30 with TH 30 220 mm 780 mm 560 mm 155 mm 140 mm Edmund Bühler GmbH - EXBED\THE00.DOC – 04/05...
Need help?
Do you have a question about the TH 15 and is the answer not in the manual?
Questions and answers