Advertisement

THIS MANUAL MUST BE READ AND UNDERSTOOD BEFORE ANYONE OPERATES THIS MACHINE!
Top Dresser
Model GT-100
Operator's Manual
Manual# 990036
Revised 01/2010

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GT-100 and is the answer not in the manual?

Questions and answers

Summary of Contents for PEQUEA GT-100

  • Page 1 Top Dresser Model GT-100 Operator’s Manual THIS MANUAL MUST BE READ AND UNDERSTOOD BEFORE ANYONE OPERATES THIS MACHINE! Manual# 990036 Revised 01/2010...
  • Page 2 PARTS AND SERVICE!! To the Owner; Thank-You for choosing a quality topdresser from Pequea Machine, Inc. We strive to give you the best equipment and the best level of service of any company. With a little care and maintenance this machine will do your work for you for many years.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS Introduction ................Serial Number ..............2 Specifications ..............2 Safety ..................Hitching .................. Loading .................. Transporting ................Adjustments ................Metering Gate Adjustment ..........6 Web and Spinner Speeds..........6 Spinner Angle ..............6 Operation ................Engine ................. 7 Control Box .................
  • Page 4: Introduction

    Contained in this manual is information pertaining to the operation, adjustment and maintenance of the Pequea GT-100. Proper care and operation will assure you many years of reliable, accurate performance. Be sure to have all operators read this manual carefully before operation.
  • Page 5: Safety

    Park on level ground and block the wheels to prevent topdresser from rolling. Pequea Machine, Inc. assumes no liability for injuries sustained because of failure to read this manual or from carelessness by the operator. Always refer to this manual for guid-...
  • Page 6: Hitching

    HITCHING Check tires to make sure they are inflated to the correct pressure. Recommended pressure is written on the sidewall of the tire. Torque the wheel bolts to 120 ft. lbs. and recheck periodically thereafter. Perform a visual check of all hardware. Vibrations from normal use can cause bolts to loosen, especially on new machinery.
  • Page 7: Loading

    LOADING Always load the topdresser on a level surface and only when hitched to the tow vehicle. Be sure to engage the parking brake of the tow vehicle. UVM Models; Be sure to have the parking brake set when loading. Always load the front first and finish at the rear.
  • Page 8: Adjustments

    ADJUSTMENTS Metering Gate Adjustment The rear metering gate is on a manually operated slide. Pull back the spring loaded locking pin and turn the me- tering disc until the gate is at the desired location. Turn the handle clockwise to raise the gate and counter-clock- wise to lower it.
  • Page 9: Operation

    OPERATION Be sure to have all hydraulic controls turned to “off” before attempting to start the engine. Engine Ensure that the gas valve is open and throttle is set at a strong idle and start engine. Choke only if necessary. If the electric start does not work, for any reason, the manual pull start rope is available as a backup.
  • Page 10 OPERATION NOTE: A number of factors will determine how the material is spread. While this manual will attempt to provide basic starting adjustments, the most effective operation will be determined from experience. • Rear Gate Opening - For most materials begin with the gate open approximately 1-1/2” ad- just to greater or lesser opening to increase or decrease material flow.
  • Page 11: Lubrication

    LUBRICATION Grease Fittings The GT-100 is designed to require minimal lubrication and maintenance. However, the impor- tance of sufficient and proper lubrication cannot be over emphasized as it is the best insurance against unnecessary repairs and will greatly increase the life and performance of the machine.
  • Page 12: Maintenance

    MAINTENANCE General Maintenance • Remove spread material buildup regularly • Protect the machine from the weather when it is not in use. (Store indoors or cover with a tarp) • Check the rubber apron belt scrapers to make sure they are down against the apron belt. •...
  • Page 13: Floor Belt Maintenance

    MAINTENANCE Drive System (Floor Belt) Maintenance • Periodically check the floor belt for proper tension and tracking. Apron belt will need to be tightened up occasionally to take up the normal stretching of the belt. If it is not tightened properly the belt may slip under a heavy load. Follow the steps below to tighten the belt.
  • Page 14: Troubleshooting

    TROUBLESHOOTING Problem Possible Cause Correction Machine is engaged but top- Material has jammed spinners Disengage machine and remove dresser is not functioning material Rear metering gate is not open Open rear gate or remove foreign or is blocked material Oil level is too low in hydraulic Add oil to reservoir reservoir Spinners are turning, but mate-...
  • Page 15: Warranty

    This Warranty does not cover, under any circumstances, any parts, components, or materials which, in the opinion of the Seller and Company, have been subjected to neglect, misuse, alteration, acci- dent, or if repaired, with parts other than those manufactured by and obtained from Pequea Machine Company.
  • Page 16: Notes

    NOTES...
  • Page 17 TurfTime Equipment LLC 800 N. Railroad Ave. New Holland, PA 17557 800-201-1031 www.turftimeeq.com [Type here]...
  • Page 18 200 Jalyn Drive P.O. Box 399 New Holland PA 17557 Phone: 717-354-4343 Fax: 717-354-8843 E-mail: pequea@pequeamachine.com www.pequeamachine.com...

Table of Contents