Do you have a question about the VIPOOL MJB VSD and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for APF VIPOOL MJB VSD
Page 1
MJB VSD INFORMATION,SETTINGS swimming pool pump...
Page 2
INDEX INFORMATION Meaning of symbols P. 3 2.A General safety instructions P. 4 2.B Operating precautions P. 4 3.A Hydraulic connections P. 5 3.B Electrical connections P. 5 Control of the pump P. 5 Operating of pump terminal box P. 7 Operating of the remote box (option) P.
About MJB VSD > DESCRIPTION - Economical pump with programmable speed as required. - Ergonomic : the pump includes a control keypad and a display Digital LED for easy programming and control. - Visual control keypad with 5 colored keys : •...
This document contains basic information for the safety of persons and property, as well as the start-up of the pump. The user and the installer must read the information contained in this document before installation and commissioning. This reference document must be kept. 2.
Page 5
3. CONNECTIONS A - Hydraulic connections • Connect the pump to the swimming pool’s hydraulic circuit using the couplings provided. • To connect the pipes to the pump, the joints are supplied with O-rings which must under all circumstances be used. •...
Page 6
A. Insertion of the 5 connection wires cable pump: Open the terminal box of the pump, Remove the plug (on the side of the pump housing), Screw the cable clamp onto the pump housing. Place the connector on the card, Pass the cable clamp, from the inside to the outside.
Page 7
5. OPERATING OF PUMP TERMINAL A.Default settings : Speed 3 = 2850 rpm Speed 2 = 2400 rpm Speed 1 = 2000 rpm Priming speed : = 2850 rpm Priming time : = 5 minutes 1000 - 2850 rpm in increments of 50 rpm. Adjustable speeds : Adjustable priming time : 0 to 10 minutes ( by 1 minute steps).
Page 8
Functions priorities: High STOP et C. Operation - Press one of the «1», «2» or «3» keys to select the preset fixed speed. If the pump is triggered after a shutdown period, it will then start in the priming mode and then move to the fixed speed selected.
Page 9
E. Priming settings The engine should be shut off (O button) to set the priming speed. Keep the “set” button, pressed at least 3 seconds, until the speed on the screen is blinking. The starting speed during priming can be chosen, using the keys and memorized with “OK”...
Page 10
6.Operation of the remote control unit (option) The housing consists in a screen and a touch pad with 5 keys : 4 navigation and 1 central «Menu / OK» key. Plug in the housing, it will light up on the main screen.
Page 11
Display shows : day and hourly programmed speeds (0 to 12 hours and 12 to 24 hours per 1 hour interval in 1 hour). Off (no filtration) Speed 1 Speed 2 Speed 3 Programming speeds according to the hours on a weekly basis.
Page 12
6.B Added functions on remote box -2 additional cable glands are supplied in the housing ref: B01P0232 - In case you use options, they must be added to the case. To do this, drill the box Ø9mm to put these cables in place. Drilling of the cable •...
Page 13
Overview of operation and possible error messages In the event of an error, the motor stops permanently. Exception error : «Undervoltage» (insufficient voltage). The motor restarts automatically as soon as the voltage becomes greater than 209 V for at least 6 seconds. If an error occurs, the system power must be turned off.
Page 14
7. CAUTIONS ON OPERATING THE PUMP ▪ The pump should operate without making any noise or vibrations. ▪ Check for any leaks on a regular basis. ▪ Clean the prefilter basket on a regular basis. ▪ Always stop the pump before handling the valve on your filter (6-way) on the swimming pool’s hydraulic circuit.
10. TROUBLESHOOTING FAULTS PROBABLE CAUSES SOLUTIONS • The pump doesn’t prime. Air leak along the suction Check the condition of the pipe. couplings and seals along the suction pipe. Incorrect motor revolution Invert phases direction (three-phase motor). electricity supply. Check the condition of the •...
Need help?
Do you have a question about the VIPOOL MJB VSD and is the answer not in the manual?
Questions and answers