Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for mlink MP290
- Page 1 MP290 Portable Wireless Gateway User Manual V1.0...
-
Page 2: Table Of Contents
MP290 Portable Wireless Gateway 目录 1. Product Overview ..........................3 2. Operation ............................. 4 2.1. Power On ..............................4 2.2. Power Off ..............................5 2.3. Activate Bluetooth ............................5 2.4. Alarm Indication ............................5 2.5. Charging ............................... 5 3. User Interface ............................5 3.1. - Page 3 MP290 Portable Wireless Gateway Read Before Operating This manual must be carefully read by all individuals who have or will have the responsibility of using, maintaining or servicing this product. The product will perform as designed only if it is used, maintained and serviced in accordance with the manufacturer’s instructions.
-
Page 4: Product Overview
• Continuous running time with full power is greater than 24 hours 2. Operation There is only one button on the MP290 portable gateway, which is used to power on/off the unit and start the Bluetooth connection function. Other operations such as registering the device, reading data, checking status, etc. -
Page 5: Power Off
In power-on state, press the button, the LED indicator will flash green, and the mLink enters the Bluetooth pairing state. At this time, you can search and connect to the mLink on the mobile app. After the connection is successful, the LED will off and the information of the mLink will be shown on mPower Suite. -
Page 6: Operating Environment
MP290 Portable Wireless Gateway 3.2. Operating Environment 3.2.1. Hardware Requirement Devices such as Android phones and Android tablets. 3.2.2. System Requirement Android（6.0 and above） 3.2.3. Operating Environment Requirement Safety area, non-hazardous. 3.3. Operation 3.3.1. Search and connect detectors 1、Run App，click button，as shown in Figure 1. - Page 7 MP290 Portable Wireless Gateway 2、Click to select detector, as shown in figure2. 图 2 连接仪器 3、Repeat steps 1 and 2, to connect other detectors. As shown in figure 3. Up to 8 detectors can be connected at the same time.
-
Page 8: Disconnect The Detectors
If the Bluetooth connection of the mLink is lost, the panel of the mLink is grayed out. Clicking on the Bluetooth connection (status) will try to reconnect. 3） Click the mLink icon or the blank area on the right to enter the detail operation screen of the mLink If the Bluetooth connection of the mLink is lost, the panel of the mLink is grayed out. - Page 9 MP290 Portable Wireless Gateway 3.3.4.1. System Click "Register Device" to start the operation of wireless device registration to the gateway. (C) mPower Electronics (Shanghai) Co., Ltd. Rev. 2019-5...
- Page 10 MP290 Portable Wireless Gateway After the device is registered, it will be shown in the list. Up to 50 devices can be registered (but 8 devices are connected at the same time). Click "Remove" to unregister the device; Click "Test" to check the device. After receiving the command, the buzzer of the device will sound and flash the light.
- Page 11 MP290 Portable Wireless Gateway After the device is registered, the wireless gateway starts to monitor the detectors. 3.3.4.2 Team Click "Team" to start real-time monitoring At the top of the screen is the status of the gateway, including the battery, Bluetooth and the last update time (updated every second).
- Page 12 MP290 Portable Wireless Gateway note: 1) Only one detector can be selected in the system at the same time. 2) When the detector is not selected, the system reads the detector information every 60 seconds; if the detector is selected, the system reads the detector information every 15 seconds.
- Page 13 MP290 Portable Wireless Gateway 3.3.4.3 Event Log Click "Event" and select a date from the date list at the bottom of the screen to view daily event records. (C) mPower Electronics (Shanghai) Co., Ltd. Rev. 2019-5...
-
Page 14: Software Information
MP290 Portable Wireless Gateway 3.4. Software Information Click the button on the main screen to show software information. Including "EULA" (End User License Agreement), "Software Settings", "Data Recording", "Event Recording" and "Software Log". 3.4.1. EULA Click "EULA" to view App License related content. -
Page 15: Software Setting
MP290 Portable Wireless Gateway 3.4.2. Software Setting Click "Software Settings" to set up the app. The settings include: 1) Software name 2) Short message notification: up to 6 mobile phone numbers 3) Email notification: up to 5 receiving mailboxes 4) Internet-based services... -
Page 16: Data Logging
MP290 Portable Wireless Gateway 3.4.3. Data Logging Click "Data Record" and select the instrument/user from the instrument/user list at the bottom of the screen to view the data record. At the same time, you can send data records by email (in txt text), and hide the record (retrieved by "show all records"... - Page 17 MP290 Portable Wireless Gateway (C) mPower Electronics (Shanghai) Co., Ltd. Rev. 2019-5...
-
Page 18: Event Log
MP290 Portable Wireless Gateway 3.4.4. Event Log Click "Event" and select a date from the date list at the bottom of the screen to view daily event records. (C) mPower Electronics (Shanghai) Co., Ltd. Rev. 2019-5... -
Page 19: Software Log
MP290 Portable Wireless Gateway 3.4.5. Software Log Click "Software Log" and select the date from the date list at the bottom of the screen to view the daily log. This log is mainly used for general app operation error checking.
Need help?
Do you have a question about the MP290 and is the answer not in the manual?
Questions and answers