Ordering Code Description Description (1) Serial Port RS-232 G G G G PS PS PS PS- - - - 110 110- - - - MB MB- - - - PS PS PS PS (1) Serial Port RS-485 www.exemys.com Rev. 3...
Power Supply Power Supply Power Supply Consumption Consumption Consumption Consumption 26mA/ 24V 18mA Operation Temperature: -15°C to 65 °C Temperatures Temperatures Temperatures Temperatures Storage Temperature: -40°C to 75 °C 1 Year Warranty Warranty Warranty Warranty Technical Support Included www.exemys.com Rev. 3...
2.2 Serial Port Wirings Serial Port Wirings Serial Port Wirings Serial Port Wirings GPS-110-MB-PShas twoserial ports; one of them is RS232 (Port A), used for configuration and monitoring, and other one RS485 (Port B) for MODBUS. www.exemys.com Rev. 3...
RS485 port wiring RS485 port wiring 2.2.2 2.2.2 RS485 RS485 port wiring port wiring To connect the device RS485 serial port to any serial device, it must be connected as can be shown in the following figure. www.exemys.com Rev. 3...
Connector Connector Connector Device has an SMA connector on the front to connect an active external GPS antenna. An active antenna with magnetic mounting and 3 meters of cable with SMA connector is provided with the device. www.exemys.com Rev. 3...
PS to a RS232 port on a Exemys Console. Exemys Console. PC and you must install an Exemys serial terminal program, named PC and you must install an Exemys serial terminal program, named Download the Exemys Console: Download the Exemys Console: http://www.exemys.com/console...
(1)-> 4 • Disabled: The NMEA frames are displayed as they come from the GPS. Parse • Enabled: The NMEA sentences are decoded for a simple reading of the user. (E|D) Example of use: 1->4->1: Interpretation Enable www.exemys.com Rev. 3...
EXCEPTIONS S S S - Enables or disables exceptions for the Modbus Port. If the option is disabled the EXCEPTION EXCEPTION GPS-110-MB-PS will respond to errors with silence, otherwise it will return an exception code. NOTE: NOTE: Stop bits are fixed at 1 in both ports NOTE: NOTE: www.exemys.com Rev. 3...
Request the current device configuration. Show Configuration Reset to the factory settings. This command must be entered 2 times for this to begin Factory Reset working. It saves the changes made and it ends the command console. www.exemys.com Rev. 3...
Seconds since12:00 AM seconds 40067 Time 40068 Minutes 40069 Seconds 40070 40071 Month 40072 Year yyyy 40073 State [active / no signal] 1 o 0 Mode [A: Autonomous / D: Differential/ E: 40074 0 o 1 o 2 Estimated] www.exemys.com Rev. 3...
Page 15
For the previous example with - - - - 34 34 34 34° ° ° ° 36,32751' 36,32751' 36,32751'it is represented in 3 registers 36,32751' -34 (with grades) 36 (with the minutes) 3275100 (the decimal part of the minutes with 7 digits) Easy online calculation is available at www.exemys.com/gpsconverter www.exemys.com Rev. 3...
P P P P o o o o rt rt rt rt B B B B – – – – MODBUS MODBUS MODBUS – – – – RS485 MODBUS RS485 RS485 RS485 Baud Rate 9600 bps Data Bits Parity Protocol Modbus RTU Modbus RTU packet time 3 [bytes Time] Exceptions Disable Modbus Slave ID www.exemys.com Rev. 3...
DIN rail and then push gently until you hear a Click! As shown in the figure. To disassemble the device of the rail DIN, pull down the metallic clip and then remove it as shown in the figure. www.exemys.com Rev. 3...
Need help?
Do you have a question about the GPS-MB and is the answer not in the manual?
Questions and answers