Advertisement
Quick Links
Advertisement
Summary of Contents for CSH ID.LATCH-BOOK.08
- Page 1 INSTRUCTION MANUAL for Installing CANE LATCH TO INVISIDOOR ID.LATCH-BOOK.08 and ID.LATCH-CANE.08...
- Page 2 Instruction Manual for Cane Latch for Invisidoor® Cane Latch Kit Includes: Strike Plate Padlock Bracket Handle Bracket (4) #8x1/2” Blk FH Philips Screw (4) #8x5/8” Blk PH Philips Screw Cane Latch Bar (2) #10x1” Blk PH Philips Screw Knob Book Kit Includes: (3) Washers (3) Lock Nuts Dummy Book...
-
Page 3: Installation Tools Needed
Back of Cabinet A. Cane Latch works for both inswing and outswing Invisidoors manufactured by CSH with a fixed shelf located at the standard dimension off the bottom. If your Invisidoor is custom and fixed shelf location is different 5/8”... - Page 4 Cane Latch Install Cane Latch Install Figure 2 7/8” Drilled 7/8” Drilled Hole Before Hole Before Hinge Side Hinge Side 2. Using a stepped approach, at the marked Installing Plate Installing Plate location, drill a ¼” through hole making sure the hole is straight and square to the cabinet 2.81”...
- Page 5 to locate for start to locate for start 29.43” Center 29.43” Center of installation of installation to Bottom to Bottom of Cabinet of Cabinet 7. Take the Handle Bracket and locate it on the back side of the cabinet over the slot Cane Latch Install as shown in Fig.
- Page 6 29.43” Center 29.43” Center 29.43” Center 29.43” Center Hinge Side Hinge Side to Bottom to Bottom to Bottom to Bottom of Cabinet of Cabinet of Cabinet of Cabinet (Same Height as (Same Height as ok Pull Install 5/8” Hole) 5/8” Hole) 5.5”...
- Page 7 of Cabinet of Cabinet of Cabinet (Same Height as of installation of installation (Same Height as 5/8” Hole 5/8” Hole 5/8” Hole) 5/8” Hole) Book Pull Install Book Pull Install 5/8” Hole 29.43” Center Side of Cabinet Side of Cabinet to Bottom 7/8”...
- Page 8 Book Pull Install Book Pull Install Book Pull Install Book Pull Install Hole Hole 29.43” Center 29.43” Center to Bottom to Bottom 7/8” Drilled 7/8” Drilled 7/8” Drilled 7/8” Drilled of Cabinet of Cabinet 4.75” 4.75” Hole Before Hole Before 4.75”...
- Page 9 5/8” Hole 5/8” Hole 5/8” Hole 5/8” Hole 5/8” Hole) 5/8” Hole) 5/8” Hole) 5/8” Hole) Book Pull Install Book Pull Install Book Pull Install Book Pull Install Transfer and Transfer and Transfer and Transfer and Drill Hole for Drill Hole for Drill Hole for Drill Hole for Loop Clamp...
- Page 10 Invisidoor Application Images...
- Page 11 NOTES...
- Page 12 Also available from CSH: Mini Barn Door Hardware Rolling Barn Door Hardware Rolling Ladders 1170 Wauwatosa Rd. Cedarburg, WI 53012 (262) 365-7960 cshardware.com REV. 1.08.21...
Need help?
Do you have a question about the ID.LATCH-BOOK.08 and is the answer not in the manual?
Questions and answers
my door is 5.5 and the instructions say drill hole at center 5.5
The correct drilling measurement for the CSH ID.LATCH-BOOK.08 door latch installation includes:
- Drill 7/8” holes (as mentioned multiple times, e.g., “7/8” Drilled”).
- Drill 3/16” thru holes (e.g., “3/16” Thru Hole”).
- Drill 5/8” holes (e.g., “5/8” Hole”).
These measurements are used for holes at the same height and for proper latch and strike plate installation. The door thickness of 5.5 inches does not change these individual hole sizes.
This answer is automatically generated