Advertisement
PRIOR TO USE
Press the rotation control button to make sure that the table rotates smoothly to the fully inverted position and back.
Failure to engage the ankle locking pin fully could result in serious injury or death!
SECURING YOUR ANKLES
Figure 2
• Pull out the locking pin to allow the front ankle clamps to snap closed against your ankles. Make sure your pant legs
do not interfere with obtaining a secure closure.
• Adjust the front ankle clamps to make sure both the front and rear ankle clamps are snug against your ankles.
Release the locking pin so that it fully engages a hole setting.
• If the locking pin does not automatically engage in a hole, push the front ankle clamps inward until the pin engages
fully in the next tightest hole setting.
Use the concept of
SEE
that there is NO space between the locking pin and its base.
ALWAYS
carefully check to be certain the ankle locking pin is fully engaged each time you use your inversion table and
make sure that both the front and rear ankle clamps are snug against your ankles, or you could fall when the table inverts.
Failure to engage the ankle locking pin fully could result in serious injury or death!
INVERTING
• Push the rotation control button in the direction of your head.
using the inversion table, do not go to full inversion. Refer to "Helpful Suggestions" on the
reverse side.
• To return upright, press the rotation control button in the direction of your feet. Rest at the
horizontal position for a minute prior to returning to start position.
• If a power failure occurs, please remain calm. Reach for the emergency crank attached with a
chain to the motor housing.
motor end and turn the crank clockwise to rotate the table upright.
Patent applies.
Teeter Hang Ups
is a registered trademark of STL
®
Inc. and Inversion International, Ltd.
Specifications subject to change without notice.
© COPYRIGHT 2004, STL Inc. and
Inversion International, Ltd.
International Law Prohibits Any Copying, 01/04-1
Owner's Manual
!
These steps must be performed carefully and precisely each time you use the inversion table!
Note:
ALWAYS
wear securely tied lace-up shoes with a flat sole, such as a normal tennis
style shoe. DO NOT wear shoes with thick soles, boots, high-tops or any shoe that extends
above the anklebone. Verify that no part of the footwear or garments can touch or interfere
with the locking pin in any way during inversion.
• Stand on the foot platform, sliding your ankles between the foam ankle clamps.
• Press your ankles back firmly against the rear ankle clamps.
• Rotate the top of the rear clamps slightly inward toward your ankles - this will increase
your comfort while inverting.
HEAR
-
FEEL
HEAR
the locking pin click into place.
FEEL
the locking pin to make sure it is fully engaged in a hole setting.
CORRECT:
LOCKING PIN
FULLY ENGAGED
!
(See Figure 4)
Insert the emergency crank into the hole at the
For information about the Teeter Hang Ups
equipment or questions about its use, please contact Customer Service at the appropriate location below:
USA & Canada:
STL Inc.
9902 162
nd
St. Ct. E., Puyallup, WA 98375
Toll Free (Phone) 800-847-0143 (Fax) 800-847-0188
Local (Phone) 253-840-5252 (Fax) 253-840-5757
(email) Info26@TeeterHangUps.com
(web) www.TeeterHangUps.com
WARNING
(See Figure 2)
-
SEE
every time you secure your ankles:
DANGER:
LOCKING PIN NOT
FULLY ENGAGED
WARNING
(See Figure 3)
2-year warranty, or if you have any problems assembling the
®
DO NOT
deviate from these instructions.
(See illustrations below)
When first
International:
Inversion International, Ltd.
PO Box: AP 59245, New Providence Island, Bahamas
(Phone) +1-242-362-1001
(Fax) +1-242-362-1002
(email) Info@InversionInternational.com
(web) www.InversionInternational.com
LP1024
Pg. 2
Advertisement
