1. Manuals
  2. Brands
  3. Teledyne Lecroy Manuals
  4. Network Hardware
  5. PCI Express M.2
  6. User manual and quick start manual

Teledyne Lecroy PCI Express M.2 User Manual And Quick Start Manual

Interposer for summit analyzers
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

PCI Express
User Manual and Quick Start Guide
Before Starting
Use this document for quick installation and setup. If you experience problems or
need more information, see the product manuals available at the Teledyne LeCroy
web site or in the Documents folder in the PCIe Protocol Suite installation DVD.
1
Introduction
The Teledyne LeCroy PCIe 3.0 M.2 Interposer, which is used with Summit™ Protocol Analyzers,
®
enables PCIe
bus traffic between a system board or tablet and a M.2/NGFF connector on a PCIe M.2
device to be monitored, captured, and recorded for protocol analysis. The M.2 interposer will support
analysis for PCIe host interfaces such as SATA Express (AHCI/PCIe) and NVM Express (NVMe) at
data rates from 2.5 GT/s up to 8.0 GT/s and link widths of up to x2 or up to x4 depending on the key
type.
M.2 Interposer for Summit Analyzers
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PCI Express M.2 and is the answer not in the manual?

Questions and answers

Related Manuals for Teledyne Lecroy PCI Express M.2

Summary of Contents for Teledyne Lecroy PCI Express M.2

  • Page 1 Teledyne LeCroy web site or in the Documents folder in the PCIe Protocol Suite installation DVD. Introduction The Teledyne LeCroy PCIe 3.0 M.2 Interposer, which is used with Summit™ Protocol Analyzers, ® enables PCIe bus traffic between a system board or tablet and a M.2/NGFF connector on a PCIe M.2...
  • Page 2 Teledyne LeCroy provides two configurations of the M.2 Interposer to support these three types of devices. One interposer is for use with B and B-M type memory modules and a second interposer is for use with M and B-M type M.2 memory modules.
  • Page 3 (following labels) and do not force them. The Extension brackets are provided to allow the user to attach and secure the Teledyne LeCroy M.2 interposer cable on the host system which usually supports different M.2 card form factors. The Teledyne LeCroy M.2 Interposer Extension Bracket Kit contains the items listed below.
  • Page 4 This procedure describes the assembly process for the Type 2260 bracket (to install the other types follow the same procedure): 1. Place the Extension bracket aligned with the counter sink screw holes. 2. Make sure the text "Type 2260" on the bracket is facing the top of the PCB where the cables are attached. 3.
  • Page 5 Exploded View Installed Side Profile Installed...

  • Page 6: Hardware Installation

    3. Install the M.2 SSD device under test (DUT) into the connector on the interposer as shown (will fit 42mm, 60mm, 80mm and 110mm). 4. Connect the Summit T3-8 Analyzer (or other compatible Teledyne LeCroy analyzer) to the interposer using the system iPass cable.

  • Page 7: Software Configuration

    Analyzer Clock Source Configuration SW1: Clock Select CABLE Clock Source Clock Source HOST_CLK Downstream sourced with host clock. DS_CLK Downstream sourced with external input DS_CLK US_CLK Upstream sourced with external input US_CLK HOST_CLK Upstream sourced with host clock. Note: Factory default is host clock SW1.1 = ON, SW1.2 = ON, SW1.3 = ON, SW1.4 = ON Note: Other switch configurations (other than those shown in the table above) are invalid.

  • Page 8: Environmental Conditions

    Teledyne LeCroy, PCIe Protocol Analysis, PCIe Protocol Suite and Product specifications are subject to change without notice. Summit T3-16, T3-8, T28, T24 and T34 are trademarks of Teledyne LeCroy reserves the right to revise the information in this Teledyne LeCroy. document without notice or penalty.

Table of Contents