Sealey BT101 Instructions page 2

Digital battery/alternator tester 12v

Hide thumbs

page of 2

/ 2
Bookmarks

3.2.3

Press the  (UP) and  (DOWN) buttons to select the battery type, SLI or SEAL (VRlA/GEl/AGm/slA) and press ENTER.

3.2.4

Press the  (UP) and  (DOWN) buttons to select the battery rating, SAE, DIN, IEC, EN or CA (mcA) and press ENTER.

3.2.5

Press the  (UP) and  (DOWN) buttons to input the battery capacity ccA or cA(mcA),

sAE: 200~1200ccA, DIn: 110~670ccA, IEc: 130~790ccA, En: 185~1125ccA or cA(mcA): 240~1440cA(mcA) and press ENTER to start the test.

3.2.6

If the display shows CHA_ (Is the battery charged?), press ENTER and using the  (UP) and  (DOWN) buttons select YES or NO and press ENTER.

3.2.7

The tester will display the actual ccA or cA and the lED lights will show one of the five following combinations:

Green LED light

The battery is good & capable of holding a charge.

XXX (ccA or cA value)

Green & Yellow LED lights

The battery is good but needs to be charged.

XXXX (ccA or cA value)

Yellow & Red LED lights

battery is discharged. The battery condition cannot be determined until it is fully charged.

Recharge & retest the battery. If reading is the same, the battery should be replaced

immediately.

XXXX (ccA or cA value)

Red LED light

The battery cannot hold a charge. It should be replaced immediately, or the battery has

at least one cell short circuit. Replace immediately.

XXXX (ccA or cA value)

Err on the screen & Second Red light

The clamps are not connected properly. Please check if the clamps are connected

properly or the tested battery is bigger than maximum testing ccA capacity.

3.3

Starting System Test (BT102)

3.3.1

The lED display will light up and show the voltage of the battery. Press ENTER to move to the next step.

3.3.2

Press the  (UP) and  (DOWN) buttons to select the system test, SYSt and press ENTER.

3.3.3

Press the  (UP) and  (DOWN) buttons to select the battery test, bAtt and press ENTER.

3.3.4

Turn off all vehicle accessories, lights, radio etc.

3.3.5

lED display shows CrAn, press ENTER.

3.3.6

start the engine. Record voltage reading after cranking the starter.

If the voltage reading is greater than 7.2V, the green lED will illuminate = starting system OK.

If the voltage reading is between 5.8 ~ 7.2V, the yellow lED will Illuminate = starting system weak, check connections, wiring and starter.

If the voltage reading is less than 5.8V, the red lED will illuminate, screen will be blank or show the battery voltage. = starting system problem, check

connections, wiring and starter.

3.4

Charging System Test (BT102)

3.4.1

After the starter test press ENTER, the screen will show CHAr, press ENTER to show the live voltage.

3.4.2

Increase the engine speed to 1200 ~ 1500rpm and read the voltage.

If voltage is between 13.4V and 14.6V, the green lED will illuminate = charging system OK.

If voltage reading is above 14.6V, the red lED will illuminate = charging voltage too high, check regulator.

If voltage reading is less than 13.4V, the yellow lED will illuminate = charging system fault, check connections, wiring, drive belt tension and alternator.

3.4.3

switch on high beam headlights, fan blower to high and rear fog lamp and repeat the above test.

If voltage is between 13.4V and 14.6V, the green lED will illuminate = charging system OK.

If voltage reading is above 14.6V, the red lED will illuminate = charging voltage too high, check regulator.

If voltage reading is less than 13.4V, the yellow lED will illuminate = charging system fault, check connections, wiring, drive belt tension and alternator.

3.4.4

Turn off engine and remove clamps from battery.

TROUBLESHOOTING

4.1

If screen shows HI: Voltage over 15V. bT101/bT102 will not operate in this condition, ensure battery being tested is 12V.

4.2

If screen shows Lo: Voltage is under 7V. bT101/bT102 will not operate in this condition, recharge the battery and repeat test, if still reading Lo replace

battery.

4.3

If the screen is blank: Ensure the clamps are connected correctly, clean battery posts if required. The voltage of the battery is too low to operate the bT101/

bT102, recharge the battery and repeat test, if screen is still blank, replace battery.

4.4

If the screen flickers or shows

replace battery.

DECLARATION OF CONFORMITY

Declaration of Conformity

We, the sole uK importer, declare that the products listed below are in conformity with the following standards and directives.

Digital Battery/Alternator Tester

Model Nos: BT101 & BT102

2004/108/Ec Emc Directive

93/68/EEc cE marking Directive

2002/95/Ec RoHs Directive

2002/96/Ec WEEE Directive

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: no liability is accepted for incorrect use of this equipment.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

_ _ _ _

: The voltage is unstable, check all connections and recharge battery if required, retest if display remains as before

Sole UK Distributor

Sealey Group,

bury st. Edmunds, suffolk.

The construction files for these products is held by the manufacturer and may be

inspected, by a national authority, upon request to Jack sealey ltd.

signed by Tim Thompson

For Jack Sealey Ltd. Sole UK importer of Sealey Professional Tools