Furuno SS542 Owner's Manual & Installation Instructions

Furuno SS542 Owner's Manual & Installation Instructions

Multi-beam sonar & depth transducer

Advertisement

Quick Links

OWNER'S GUIDE & INSTALLATION INSTRUCTIONS
Thru-Hull Mount
Installation of the anti-rotation bolt is mandatory!
The anti-rotation bolt holds the fairing firmly in place. Failure to install the anti-
rotation bolt may result in the fairing rotating while the boat is underway. The
effect may be violent movement and loss of steering. This could result in serious
injury or death to passengers and/or damage to the boat or other property.
Follow the precautions below for optimal product
performance and to reduce the risk of property damage,
personal injury, and/or death.
WARNING: The transducer must be installed with a High-
Performance Fairing.
WARNING: When installing the High-Performance Fairing
carefully follow these installation instructions.
WARNING: Always wear safety glasses, a dust mask, and
ear protection when installing.
WARNING: The fairing must be installed parallel to the keel
to ensure proper boat handling.
WARNING: Do not install a fairing that has been mis-cut.
Replace it.
• Cutting the fairing at an angle greater than the maximum
allowed will cut into the transducer and/or bolt pocket,
thus weakening the fairing.
• Do not allow any gap between the fairing and the hull that is
greater than 3mm (1/8"). When the boat is underway,
water will enter any gaps and push against the fairing with
considerable force, possibly rotating it.
WARNING: Immediately check for leaks when the boat is
placed in the water. Do not leave the boat unchecked for
more than three hours. Even a small leak may allow
considerable water to accumulate.
CAUTION: Stainless steel transducer in a metal hull—
Use sleeving to isolate the stainless steel transducer and
anti-rotation bolt from the metal hull. Failure to do so will
cause electrolytic corrosion.
CAUTION: Never pull, carry, or hold the transducer by the
cables as this may sever internal connections.
CAUTION: Never strike the transducer.
Multi-beam Sonar & Depth Transducer
Model SS542
WARNING
with Temperature Sensor & High-Performance Fairing
CAUTION: Do not over-tighten the hull nut and the nut on
the anti-rotation bolt, crushing the fairing and/or hull.
CAUTION: The transducer and the yellow triangular plug
must be flush with the fairing for smooth water flow under the
transducer.
CAUTION: Never use solvents. Cleaner, fuel, sealant, paint,
and other products may contain solvents that can damage
plastic parts, especially the transducer's face.
IMPORTANT: Read the instructions completely before
proceeding with the installation. These instructions
supersede any other instructions in your instrument manual
if they differ.

Applications

• Stainless steel transducer compatible with all hull materials.
Recommended for aluminum hulls to prevent electrolytic corrosion
provided the stainless steel transducer is isolated from the metal hull.
• Maximum deadrise angle of 20°.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SS542 and is the answer not in the manual?

Questions and answers

Summary of Contents for Furuno SS542

  • Page 1 OWNER’S GUIDE & INSTALLATION INSTRUCTIONS Thru-Hull Mount Multi-beam Sonar & Depth Transducer with Temperature Sensor & High-Performance Fairing Model SS542 WARNING Installation of the anti-rotation bolt is mandatory! The anti-rotation bolt holds the fairing firmly in place. Failure to install the anti- rotation bolt may result in the fairing rotating while the boat is underway.
  • Page 2 displacement hull aft view pressure waves stem hull nut 1/3 aft backing block (Load Waterline Length) 150-300mm (6-12") slope of hull isolation sleeve planing hulls deadrise angle hull (metal) parallel to water surface outboard and I/O min. fairing thickness inboard 74mm (2-7/8") transducer marine sealant...
  • Page 3 High- Performance Fairing SS542 triangular plug with curved marine sealant on following (shown in red): surface facing - transducer, extending above hull nut 1/4" (NOT surface that will touch water) outward - fairing that contacts hull...
  • Page 4 & block washer toward the bow. hull High- Performance Fairing SS542 isolation sleeve triangular plug with curved marine sealant on following (shown in red): surface facing - transducer, extending above hull nut 1/4" (NOT surface that will touch water) outward...
  • Page 5 Stainless steel transducer in a metal hull—To prevent Dimension equal to electrolytic corrosion, the stainless steel anti-rotation bolt must the thickness of the inner skin hull’s outer skin to be isolated from the metal hull. Slide the isolation sleeve over the ensure adequate clearance bedded anti-rotation bolt as far down as possible (Figure 6).
  • Page 6 Do not remove this tag. When ordering, specify the part number, date, and frequency in kHz. For convenient reference, record this information below. Part No.________________Date___________Frequency_________kHz Lost, broken, and worn parts should be replaced immediately. Hull Nut High-Performance Fairing Please contact your Furuno dealer to obtain parts.

Table of Contents