Ryobi R18RS Original Instructions Manual page 3

Safety, performance, and dependability have been given
top priority in the design of your reciprocating saw.
INTENDED USE
The reciprocating saw is intended to be used only by
adults who have read and understood the instructions and
warnings in this manual and can be considered responsible
for their actions. With appropriate blades
reciprocating saw is designed to cut wood, plastic, drywall
and metal up to the depth described in the speci cation
table. The reciprocating saw is designed for handheld
use; it is not to be mounted onto a workbench unless
speci c instructions are given about how to do this by the
manufacturer of the product.
Do not use the product in any way other than those stated
for intended use.
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
RECIPROCATING SAW SAFETY WARNINGS
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
Protect your lungs. Wear a dust mask if operation is
dusty.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of re, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in uid or allow a uid to
ow inside them. Corrosive or conductive uids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
RESIDUAL RISKS
Even when the reciprocating saw is used as prescribed, it is
still impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
Injury caused by vibration
– Use the lowest speed setting which achieves the
tted, the
task. Limit exposure. See risk reduction.
Injury caused by dust
– Wear eye protection at all times. Wear appropriate
dust mask with suitable filters that can protect
against particles from the material being worked on.
Do not eat, drink, or smoke in the work area. Ensure
adequate ventilation.
Electric shock
– The blade may contact hidden wiring causing
parts of the product to become live. Always hold
the product by the designated handles and take
care when blind cutting into walls and floors where
cables may be hidden.
NOTE: When working on walls, ceilings, or floors, take
care to avoid electric cables and gas or water pipes.
The product must be operated with both hands.
Injury from contact with the cutting blade
– The blades are very sharp and will become hot
during use. Wear gloves when changing blades.
Keep hands away from the cutting area at all times.
Clamp the workpiece whenever possible.
Injury caused by noise
– Prolonged exposure to noise will increase the risk
of hearing damage, and the effects are cumulative.
When using power tools for any extended period of
time, wear hearing protection.
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the ngers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking, and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
Keep your body warm in cold weather. When operating
the product, wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
After each period of operation, exercise to increase
blood circulation.
Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English | 1