Summary of Contents for SNC LYTE LYNX P30112
- Page 1 6- Slot Card Shelf Description & Installation P30112 Print ed in USA – 09/ 11 TO395 Rev. E...
-
Page 2: Table Of Contents
Table of Cont ent s Page 1. 0 PRODUCT SCOPE 2. 0 PRODUCT OVERVIEW 2. 1 Int ended Uses 2. 2 Syst em Requirement s 2. 3 Part s List 2. 4 Physical Charact erist ics 3. 0 PRODUCT FEATURES 3. -
Page 3: Product Scope
This document describes t he t echnical specif icat ions, t echnical requirement s and inst allat ion inst ruct ions for t he P30112 SNC Lyt e Lynx® 6-Sl ot Card Shel f . It provides an underst anding of t he basic f unct ions and f eat ures avail abl e wit h t his product . -
Page 4: Product Features
Powering The subst at ion side of most SNC Lyt e Lynx® and Tel el ine Isol at or* f iber opt ic isol at ion cards requires a suppl y of -24VDC or -48VDC power t o operat e. Float ed 48VDC or 130VDC bat t ery and 120VAC power is commonl y avail abl e at most power subst at ions. -
Page 5: Card Shelf Mount Ing
CAUTION: Any met all ic shielding on t he incoming CO/ Remot e pair must be isol at ed f rom subst at ion grounds al l t he way f rom t he net work l ow vol t age int erf ace (300 vol t peak GPR point per IEEE St andard 487) t o t he ent ry int o t he Card Shel f . -
Page 6: St At Ion Side Pair Designat Ions
J25 Power J28 LED Indicator Feed Jumper S5 PRI/SEC Figure 1: St at ion Side (Upper) Backpl ane 5. 2 St at ion Side Pair Designat ions Each of t he six (6) sl ot s wil l support t wo (2) pairs. The f irst pair is connect ed t o t he l ef t side of t he backpl ane j acks and assigned a numeric designat ion (i. -
Page 7: St At Ion Power/ Ground Connect Ions
Table 2: Station Side Pin Configurations Station Side SLOT # CONNECTOR COLOR – TIP PAIR COLOR – RING CONNECTOR ST2-28 WHT/ BLU – T1 BLU/ WHT – R1 ST2-27 ST2-26 WHT/ ORN – TA ORN/ WHT – RA ST2-25 ST2-24 WHT/ GRN –... - Page 8 External Connections Just bel ow t he st at ion cabl e ent rance is a cl ust er of four it ems. See Figure 2. 1) LED – The f irst of t hese it ems (f urt hest t o t he l eft ) is an LED t hat when l it indicat es 24VDC or 48 VDC GROUNDED power is avail abl e at each slot in t he card shel f .
- Page 9 To bring external 24VDC into the card shelf: A separat e wire can be brought int o t he card shelf and connect ed direct ly t o t he ST1-2 (GND) and ST1-1 (–24V) t erminal block posit ions. The LED indicat or j umper J28 shoul d be set t o "24V”...
-
Page 10: Installation - Co/ Remote Side Connections
Powering Cards Requiring Other Than 24/ 48VDC GROUNDED Some isol at ion cards have special powering requirement s, i. e. 48VDC FLOATED, 130VDC FLOATED, or 120VAC. 48VDC/ 130VDC FLOATING – Wit h t he bat t ery t erminal s connect ed properl y as described at t he above sect ion (5. -
Page 11: Remot E Side Pair Designat Ions
Figure 5 Remot e Side Terminal Bl ocks 6. 2 Remot e Side Pair Designat ions Each of t he t wel ve (12) sl ot s will support t wo (2) pairs. The f irst pair is connect ed t o t he l ef t side of t he backpl ane j acks and assigned a numeric designat ion (i. -
Page 12: Remot E Ground
6. 3 Remot e Ground When Surge/ Lightning Arrester is NOT Used : If user has concl uded t hat a surge arrest er is not needed for t he inst all at ion, t hen t he dedicat ed cabl e pairs are normal ly connect ed in an insul at ed spl ice case or t erminal box t o t he card shel f cabl e st ub. -
Page 13: Trouble Shooting
NOTE: The SW1 backpl ane swit ches must be in t he down or “ St andard” posit ion t o connect t he CTE of slot s J1 t o J3 and J9 t o J11. SW1 SWITCH ON REMOTE BACKPLANE Bet ween sl ot s J4 and J5 is an up/ down swit ch marked “... -
Page 14: 8. 0 Pin Out Diagrams
Remot e (Lower) Backpl ane For f urt her inf ormat ion or f or t echnical support – call 800-558-3325 or visit www. sncmf g. com SNC Manufacturing Co., Inc 101 West Waukau Ave., Oshkosh, WI 54902-7299 800-558-3325 or 920-231-7370 FAX 920-231-1090 E-mail: telecom@sncmfg.com...
Need help?
Do you have a question about the LYTE LYNX P30112 and is the answer not in the manual?
Questions and answers