Subscribe to Our Youtube Channel
Summary of Contents for Trikdis GV14
- Page 1 CONTROLLER GV14 User Manual Draugystes g. 17, LT-51229 Kaunas E-mail: info@trikdis.lt www.trikdis.lt...
-
Page 2: Table Of Contents
Purpose of the document This document describes controller GV14, its use, features, operation and how to set operation parameters. Contents Controller GV14 ..............................3 Technical parameters ............................4 Equipment ................................. 4 Controller components ............................. 4 Purpose of contacts ............................... 5 Light indication ................................ -
Page 3: Controller Gv14
Controller GV14 Controller GV14 is a remote control device for electrotechnical equipment (opening or raising the gates, heating or ventilating the premises, watering the lawn or the greenhouse, controlling pump, boiler, transporter and other systems). Control commands are transmitted via GSM. -
Page 4: Technical Parameters
Parameters setting b) Special syntax SMS messages Controller dimensions and weight 79 x 65 x 25 mm aluminium case, 120 g Equipment Controller GV14 1 pc. Adhesive mounting tape (7 cm) 1 pc Controller components 1. SMA connection of GSM antenna 2. -
Page 5: Purpose Of Contacts
Follow this controller installation procedure in order to ensure that controller will be available for use to everyone with whom SIM card phone number is shared. 1. Purchase controller GV14. Factory settings should not be changed! 2. Insert the SIM card of the desired network provider into the controller. - Page 6 b) Drill three holes in the mounting case (see picture below) and screw the controller using to screws M3x6. c) Insert the controller into the plastic holder PH which fitted inside the mounting case. 4 holes Ø3,5 4 count. Ø6,5 4.
-
Page 7: Wiring Diagrams
Event is recorded when INx-COM circuit is broken INx-COM circuit is connected Configuration using software TrikdisConfig All controller GV14 operation parameters are set using computer software TrikdisConfig. Software may be found on www.trikdis.lt Connecting to a computer 1. Connect the controller to the computer USB slot using a USB cable (e.g., USB type A to Mini-B 5- pin cable). -
Page 8: Configuration Of Controller Operation
Information about the connected device In the program status bar will be dispayed where: Status Done is displayed after every successful reading or saving action GV14 Product name Controller serial number Controller firmware boot loader version Controller firmware version Controller hardware version... -
Page 9: User List
Parameter Description Controller identification name that will be featured in every Object name controller SMS message a) All – controlled by anyone calling the controller SIM card number. b) From the phone numbers list and administrators – controlled by anyone calling the controller SIM card number and having their phone number on User and Administrator lists. -
Page 10: Administrator List
Enter User names (13 symbol max) and their telephone numbers (16 symbol max) Administrator list Enter at least one administrator name and their phone number in the tab SMS addressees in the menu SMS messages. Controller will follow the commands received from these numbers and will send them SMS messages. -
Page 11: Recording And Saving The Configuration
3. Click Disconnect to disconnect the programmed device. Updating the controller firmware Manufacturer may improve the operation of controller GV14 and release a new controller firmware version. Every user has an opportunity to update operation of their controller. 1. Connect the controller to a computer using USB cable. -
Page 12: Configuration And Control Using Sms Messages
7. Click OK. All operation settings will remain the same after the update. Configuration and control using SMS messages Controller GV14 parameters may be set and changed by sending SMS messages from a phone number, which is on the administrator list. In case there are not any entered administrator phone numbers, become an administrator by sending the following SMS message to the controlled SIM card number: 123456 SETAP APNR1:+370xxxxxxx. - Page 13 SETH GV14 answers to the call : Rejects the call whithout picking up the hook (default); Picks up the hook and holds connection for the set period of time; E.g.: 123456 SETH 05 SETL Setting the communication language: English (default);...
-
Page 14: Automatics Control
E.g.: 123456 LISTU Automatics control Phone call 1. Call to the controller GV14 using a SIM card number. 2. Control command will be implemented immediately after the controller rejects the call. SMS message Note: Phone number must be on the controller‘s administrator list. -
Page 15: Controller Sms Messages
SMS. Every time 12 V power supply voltage is turned on, administrators are send a SMS message: SMS text Description Dev: GV14 Device name IMEI: 863071014319393 IMEI code of the GSM modem SN: 000002 Serial number of the controller FW: 0.02... -
Page 16: Safety Requirements
Safety requirements Be sure to familiarise yourself with this manual before using the controller. Controller may only be set up and maintained by trained specialists, who possess knowledge about operation of GSM devices and their safety requirements. External power supply must be turned off when controlled is being set up! Controller must be set up in limited access areas and in safe distance from sensitive electronic equipment in the premises.
Need help?
Do you have a question about the GV14 and is the answer not in the manual?
Questions and answers