Advertisement
Operating Instructions and Parts Manual
PURPOSE
The OEM Rotary Barrel Pump is a hand-operated pump constructed with
a polypropylene body, Ryton (PPS Polyphenylene Sulfide) rotor and vanes
for resistance to chemicals. This pump is capable of transferring material
at 300cc per revolution (up to 10 gallons per minute at 70 revolutions per
minute) with temperatures up to 130 degrees F. Suitable for water based
solutions of acid, alkalis and salt, some organic solvent, water and all
petroleum products. Most organic acids, solvents, waxes, plating solution,
detergents & water-soluble inorganic chemicals. Also suitable for water based
chemicals in a variety of automotive, industrial and commercial applications.
WARNING
NOT SUITABLE FOR USE WITH GASOLINE, DIESEL
EXHAUST FLUID (DEF), NITRIC ACID ETC. DO NOT
PUMP USED, DIRTY OIL OR FLUIDS IN THIS PUMP.
IT IS SOLEY THE OPERATORS REPSONIBILITY
TO DETERMINE IF A FLUID IS COMPATIBLE WITH
THIS PUMP. IF IN DOUBT CONTACT THE FLUID
MANUFACTURER OR OEM TOOLS.
PRODUCT SPECIFICATIONS
Flow Rate:
Capacity:
Bung Adapter:
Suction Tube Length:
Suction Tube Diameter:
Discharge Spout:
Applicable Drums:
WARNING
TOXIC FLUID HAZARD:
HAZARDOUS FLUID OR TOXIC FUMES CAN CAUSE SERIOUS INJURY OR DEATH
IF SPLASHED IN THE EYES OR ON THE SKIN, INHALED, OR SWALLOWED.
KNOW THE SPECIFIC HAZARDS OF THE FLUID YOU ARE USING. STORE
HAZARDOUS FLUID IN AN APPROVED CONTAINER. DISPOSE OF HAZARDOUS
FLUID ACCORDING TO ALL LOCAL, STATE AND NATIONAL GUIDELINES.
ALWAYS WEAR PROTECTIVE EYEWEAR, GLOVES, CLOTHING AND RESPIRATOR
AS RECOMMENDED BY THE FLUID AND SOLVENT MANUFACTURER.
WARNING
FIRE AND EXPLOSION HAZARD:
• EXTINGUISH ALL OPEN FLAMES OR PILOT LIGHTS IN THE WORK AREA.
• DO NOT SMOKE IN THE WORK AREA.
• DO NOT TURN ON OR OFF ANY LIGHT SWITCH IN THE WORK AREA WHILE
OPERATING OR IF FUMES ARE PRESENT.
• DO NOT OPERATE A GASOLINE ENGINE IN THE WORK AREA.
• KEEP A FIRE EXTINGUISHER IN THE WORK AREA.
• KEEP THE WORK AREA FREE OF DEBRIS, INCLUDING SOLVENT, RAGS,
AND GASOLINE.
04/15
2015 ©OEMTOOLS
Up to 10 GPM
300 cc per revolution
2" Thread
42"
1"
3/4"
30, 55 Gallon and some 15 Gallon.
ROTARY BARREL PUMP
POLYPROPYLENE
INSTRUCTIONS:
1. Attach Handle:
a. Remove Nut from the threaded shaft of the
Handle.
b. Loosely tighten Nut against the Handle.
c. Insert the Nut into the Crank Arm, then screw Handle into the Crank
Arm until threaded rod is flush with the backside of Nut.
d. Loosen Nut from the Handle and tighten
Arm to lock threads. Handle
e. Then attach Handle Assembly to Pump Body Shaft and tighten set
screw.
NOTE: Use a compatible, liquid thread sealant or PTFE tape on all male
threads. Tighten all connections firmly to avoid air or fluid leaks. Do not
overtighten plastic threads.
2. Slide the Bung Nut onto the top portion of the Suction Tube.
Do not tighten.
3. Thread the Suction Tube into the inlet side of Pump. Attach extensions
as needed for your drum size.
4. Insert Suction Tube into the drum's 2" Bung opening.
5. Thread the Bung Nut into the tank.
6. Position the Pump Head at the desired height and angle and tighten
the Bung Nut Locking Screw.
NOTE: If the pump position is too high the pick-up tube cannot
capture fluid.
7. Assemble and thread the Delivery Spout onto the output side
of Pump.
MAINTENANCE:
Weekly: Spray a Teflon lubricant into the Pump Body.
3
24470
against the Crank
should spin freely.
Advertisement
