Subscribe to Our Youtube Channel
Related Manuals for Identiv uTrust TS
Summary of Contents for Identiv uTrust TS
- Page 1 User Manual uTrust TS Contact Keypad Reader 8216 Version 1.1 Confidential Author Sixtus Stanly Version Date 11-Aug-2020 Document no 821601_UM...
- Page 2 Document History Version Date Description of Change Author 14-Feb-2019 Initial version Sixtus Stanly 11-Aug-2020 Added ISED French notes Sixtus Stanly...
-
Page 3: Table Of Contents
TS Contact Keypad Reader Contents Introduction ..........................4 Reader ............................4 Functionality ..........................4 Front/Top Casing ........................4 Rear View w/o back plate ......................5 Product details ........................... 8 Specifications ..........................8 Product Label ..........................8 Product Certification ID’s ......................9 FCC Certification ID - MBPTSKPSC-00 ................... -
Page 4: Introduction
TS Contact Keypad Reader 1.0 Introduction This document details the Physical Access Control Reader uTrust TS Contact Keypad Reader and its basic user instruction and installation procedures. The 8216 reader extends the features supported by the 8210 readers, by adding interfaces for accessing a Contact Smart Card and a SAM interface. -
Page 5: Rear View W/O Back Plate
TS Contact Keypad Reader Rear View w/o back plate Page 5 of 15... - Page 6 TS Contact Keypad Reader Reader with Terminal connector Reader with Pigtail cable Page 6 of 15...
- Page 7 TS Contact Keypad Reader Rear View with Backplate Back plate Page 7 of 15...
-
Page 8: Product Details
TS Contact Keypad Reader 3.0 Product details Model Name : 8216 Device Type : RFID reader, 13.56MHz (HF) / 125 KHz (LF), keypad with Contact smartcard Slot for ID-1 sized cards and SAM slot. Physical Access control Reader (accessory equipment) -
Page 9: Product Certification Id's
TS Contact Keypad Reader 6.0 Product Certification ID’s 6.1 FCC Certification ID - MBPTSKPSC-00 6.2 IC Certification ID - 7485A-TSKPSCR0 7.0 Installation details Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and the authorities having jurisdiction. -
Page 10: Connector Information
TS Contact Keypad Reader 7.3 Connector Information 7.3.1 Pinout diagram Shield Ground/ Drain – Black wire should be connected to the cable shield. Caution: During Wiring make sure that the +VDC lines does not make contact with any other cables, as it might affect reader functionality/ cause damage to the reader. -
Page 11: Mounting The Reader
TS Contact Keypad Reader 7.4 Mounting the Reader 7.4.1 Reference for location of mounting holes on the wall Phoenix connector Reader – 4 Holes and 1 Slot 7.4.2 Reader Installation Steps a. Make the required holes on the wall as per the backplate drawing above. - Page 12 TS Contact Keypad Reader Page 12 of 15...
-
Page 13: Power Up And Testing
TS Contact Keypad Reader Power up and Testing Turn power on The LED blinks 3 times green with a long beep, then turns red Present a card Contactless card - The LED blinks green, and a short Beep is heard... - Page 14 TS Contact Keypad Reader Press Key Buzzer tone & backlight LED blinks Page 14 of 15...
-
Page 15: Certifications
(2) Cet appareil doit accepter toute interférence, y compris les interférences pouvant fonctionnement indésirable de l'appareil 9.3 CE Identiv hereby declares that the uTrust TS Contact Keypad Reader Model 8216 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Page 15 of 15...
Need help?
Do you have a question about the uTrust TS and is the answer not in the manual?
Questions and answers