Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for joule InvaVent 350
Summary of Contents for joule InvaVent 350
- Page 1 Instructions Booklet COD. 5.471.084.937 30/02/2018...
-
Page 2: Table Of Contents
Safety........3 Joule cannot assume any responsibility for damage to Items supplied . -
Page 3: Description And Use
• Inspect the appliance periodically for visible defects. If the appliance is defective in any way, do not use it; contact a Joule Technical Support Centre without delay. • If the appliance does not function correctly or develops a fault, contact a Joule Technical Support Centre without delay. Ensure that only original Joule replacement parts are used for any repairs. -
Page 4: Items Supplied
ENGLISH • If the power cable is damaged, have it replaced without delay by a Joule Technical Support Centre. • Should the appliance be dropped or suffer heavy impact, have it checked without delay by a Joule Technical Support Centre. -
Page 5: Installation
ENGLISH Installation NOTE The appliance is not suitable for outdoor installation. The appliance must be installed in accordance with current safety regulations in the destination country, and with the instructions in this booklet. The appliance must be installed on an internal surface or wall of the home structurally suited to holding its weight (max. 50 kg). To mount the appliance, use Brackets kit for Wall mounting (supplied with produtc) or Brackets kit for Suspended floor mounting (optional). - Page 6 Connecting the Pre-heater optional On the Stale air outlet duct (See Fig. 3, letter (A)), you can connect the Joule Pre-Heater (optional), which must be fitted and set up by the installer. The minimum distance of the preheater from the appliance is 500 mm.
-
Page 7: Electrical Connections
ENGLISH IMPORTANT: Fig. 4 - Winter operating: high probability of condensate forming; drain hoses must be connected, with a siphon trap. “a”. - Summer operating: probability of condensate forming; drain hoses should be connected, with a siphon trap. “b”. Fig. 5 The siphon must be created observing indicated dimensions, otherwise correct operation of the appliance cannot be guaranteed. -
Page 8: Use
ENGLISH Appliance is automatically managed by an electronic control system. Appliance can automatically choose the most suitable operating mode, depending on the outside temperature. When the appliance is switched, both motors will stop to allow repositioning of the by-pass valve. After, motors will start up again. - Page 9 ENGLISH 2) After 24 h from the last By-Pass valve opening Appliance forces a By-pass activating to check the effective position of the valve: - if the valve is opened, force the opening; - if the valve is closed, force the closing. This is a normal system procedure and should not be perceived as a malfunction.
-
Page 10: Operation And Use
ENGLISH Operation and use User interface The following operations can be performed through the user interface: • Temperature control; • Air speed adjustment; • Weekly air speed programming (only NOT UK Markets); • Alarms management. The below table shows functions related to each key on the interface. Function 1 recall key. - Page 11 ENGLISH Some examples of the HOME screen are shown below. Bypass NoFrost Ext + 5°C Int +22°C Progr Exh +18°C 03/04/2017 12:30 Equipment start-up/shut-down (only NO UK markets) Only NOT UK: If the equipment is switched off, the "HOME" page will display "Off" at the centre. To access equipment: from the “HOME”...
- Page 12 ENGLISH User "Operations menu" page Enter the password as shown in the figure to access the user "Operations menu." From this new page you can manage: • By-pass MAN 12 h forced activation of the function: “By-pass”; • Holiday activating “Holiday” function: appliance always operating at Min speed; •...
- Page 13 ENGLISH From this new page you can manage: SETP BYP. [ ▲ ] • Setp Byp. “By-pass” function activation depends on the “Setp Byp” temperature. “Setp Byp” is selectable into a variable range between: 15°C & 30°C (default value = 18°C). LIFE TIME [ ▲...
- Page 14 ENGLISH “Setting No Frost Menu” Page From “Installer menu" page, you can select “No Frost”, in order to join to “Setting No Frost”. Pressing the [ ] key will display: Pre-set values NO FROST UN-BALAN YES (enabled) [ ▲ ] UN-BALAN.
- Page 15 ENGLISH “Setting speed Menu” Page From “Installer menu" page, you can select “Speed”, in order to join to “Setting speed”. Pressing the [ ] key will display: SPEED VEXH1 [ ▲ ] [ ▲ ] VSUP1 VEXH1 VSUP2 VEXH2 VSUP3 VEXH3 VSUP B VEXH B...
- Page 16 ENGLISH Pre-alarm: “Filters checking” After the preset time has elapsed, "Alarm" appears in "HOME" and the note "Check clean filter" in the "Alarms" page. To replace the filters, follow the instructions in "Maintenance and Cleaning". Pressing the [ ] key will display: Filters Alarm [ ▲...
- Page 17 ENGLISH Alarm: "Ext Probe" damaged The equipment is equipped with an External temperature probe that measures the air temperature extracted from outside. The Probe Fault reports in "HOME" the message "Alarm " "Lock " and in the "Alarms" page the note "Ext probe Call Service".
- Page 18 ENGLISH "Date & Time" page You can set the day of the week and the current time on this page. Go to the "Date & Time" row on the "Configuration" page and press the key [ ] to go to a new page as shown in the figures below. [ ▲...
- Page 19 ENGLISH Press the [ ] key to confirm: The "Program" page allows you to assign up to 6 time intervals with different speeds, including equipment shut-down. Press the [▲] or [▼] key multiple times to scroll all the intervals. NOTE At the unspecified intervals, the equipment operates at the speed that is set manually on the "HOME"...
-
Page 20: Maintenance/Cleaning
ENGLISH Maintenance and cleaning Fig. 35-36 Ordinary maintenance - Filters Recommended maintenance intervals: because levels of air pollution depend typically on geographical location and are variable, the life of the filters will be similarly variable. With this general consideration in mind, check following alarms for filter maintenance: •... -
Page 21: Important Information Regarding Eco-Compatible Disposal
ENGLISH Important information concerning the environmentally compatible disposal IN CERTAIN EUROPEAN UNION COUNTRIES THIS PRODUCT DOES NOT FALL WITHIN THE REQUIREMENTS OF THE NATIONAL LAWS IMPLEMENTING DIRECTIVE WEEE, AND IN THESE COUNTRIES THE PRODUCT IS NOT SUBJECT TO SEPARATE DISPOSAL OPERATIONS AT THE END OF ITS WORKING LIFE. This product conforms to EU 2012/19/EC This appliance bears the symbol of the barred waste bin. - Page 23 ∆ h > 50 mm ≥ 60 mm...
- Page 24 0≤β<2° β 0≤α<2° α To unscrew Torx T25...
- Page 26 To screw Torx T25 Torque: 1,0 N/m To unscrew Torx T25...
- Page 27 To screw Torx T25 Torque: 1,0 N/m...
- Page 28 Mains 2 poles switch OPTIONAL: Preheater (remote 230Vac relay coil ) OPTIONAL: Dry contact (remote switch / relay ) Remote HMI POWER SUPPLY GNYE MAINS MAINS 230V ~50Hz PREH PREH Mains 2 poles switch REMOTE CONTROL Remote HMI...
- Page 29 POWER SUPPLY + PRE-HEATER GNYE MAINS 230V ~50Hz MAINS PREH PREH 230V ~50Hz Mains 2 poles switch Preheater (remote 230Vac relay coil ) C HCS cod. 12.994 Dry contact (remote switch / relay ) TM L BOOST BOOST C TEMP cod. 12.992 C PIR cod.
- Page 32 JOULE IE JOULE UK mail Kylemore Park West, Ballyfermont, Dublin 10 mail Unit 17C&D Power Road, Plantation Bus. Pk. +353 (1) 623 7080 Bromborought, Wirral, CH62 3RN +353 (1) 626 9337 +44 (0) 1513 551 094 info@joule.ie +44 (0) 1513 568 336 www.joule.ie...
- Page 34 CERTIFICATE OF WORK PERFORMED UNDER GUARANTEE DATE OF WORK STAMP OF TECHNICAL ASSISTANCE CENTRE CERTIFICATE OF WORK PERFORMED UNDER GUARANTEE DATE OF WORK STAMP OF TECHNICAL ASSISTANCE CENTRE CERTIFICATE OF WORK PERFORMED UNDER GUARANTEE DATE OF WORK STAMP OF TECHNICAL ASSISTANCE CENTRE CERTIFICATE OF WORK PERFORMED UNDER GUARANTEE DATE OF WORK STAMP OF TECHNICAL ASSISTANCE CENTRE...
- Page 35 CONDITION OF WARRANTY This guarantee is offered as an extra benefit and does not affect your legal rights. All electrical appliances produced by Joule are guaranteed by the Company for 2 years against faulty material or workmanship. If any part is found to be defective in this way within the first twentyfour months from the...
- Page 36 GUARANTEE TO BE RETAINED Purchase date This warranty must be attached to the appliance should it need to be returned for servicing. YEARS N.B. Guarantee is only valid if all details are completed correctly. Stamp of supplier Mailing date CONF. COLL.
Need help?
Do you have a question about the InvaVent 350 and is the answer not in the manual?
Questions and answers
what is the warranty on the invavent 350
The Joule 350 is guaranteed for 2 years against faulty material or workmanship. The warranty covers replacement or repair of defective parts at no charge for materials, labor, or transportation, provided the appliance is used according to the instructions, connected to a suitable electricity supply, and not misused, neglected, damaged, modified, or repaired by unauthorized persons.
This answer is automatically generated