Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Fastora Fastora NAS T2
- Page 1 FASTORA NAST2 Hardware Installation Guide For service person only...
- Page 2 Disclaimers The information in this manual has been carefully checked and is believed to be accurate. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of patents or other rights of third parties, which may result from its use. AXIOMTEK assumes no responsibility for any inaccuracies that may be contained in this document.
-
Page 3: Safety Approvals
CE Marking FCC Class A FCC Compliance This equipment has been tested and complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 4: Safety Precautions
Before getting started, read the following important cautions. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge. Disconnect the power cords from the FASTORA NAS before making any installation. -
Page 5: Table Of Contents
Chapter 1 Introduction ------------------------------------------------------------------- 1 General Description ... 1 Standard Features ... 2 System Specifications ... 2 Dimensions ... 5 Rear Panel Outlets ... 6 Front Panel Outlets ... 6 Chapter 2 Installation Procedures ------------------------------------------------ 7 Preinstallation Checklist... 7 2.1.1 Installing a hard-swappable hard drive ... 7 Chapter 3 Starting the Appliance -------------------------------------------------11 Hardware installation before starting the appliance ... - Page 6 This page does not contain any information.
-
Page 7: Chapter 1 Introduction
This chapter states general information and detailed specifications of the FASTORA NAST2 Network Attached Storage server. Chapter 1 includes the following sections: General Description Features System Specifications General Description The FASTORA NAST2 server is designed for workgroup and solution providers those have networked storage requirements across heterogeneous Microsoft Windows ... -
Page 8: Standard Features
FASTORA NAST2 Server Hardware Installation Guide Standard Features Tower unit design Hassle-free management via a browser interface or Windows setup utility for DHCP automatic IP assignment 24 x 7 fault-resilient storage appliance; Auto-notification alert system High-performance RAID at RAID 0, 1 with hot- spare, on-line rebuild. 2 ATA-66/100 hot-swappable IDE HDD bays. - Page 9 Serial Port: One UART Ethernet: One 10/100 Base-T Ethernet and one optional Gigabit Ethernet Supporting fail-over Compact-FlashTM: One IDE interface CompactFlash Dimensions: 120.9mm (W) x 183.0mm (H) x 265.8mm (D) Weight: Approx. 4kg with Power supplies, without any hard drive Operation environment: Air temperature: 10°...
-
Page 10: Other Features
FASTORA NAST2 Server Hardware Installation Guide Other Features: Windows -based setup utility for DHCP automatic IP assignment for Microsoft 95/98/NT/2000/XP Windows -based (Non-Windows Microsoft Double-byte language support RAID management Browser-based software update Restore default settings -based) setup utility for DHCP automatic IP assignment for ... -
Page 11: Dimensions
FASTORA NAST2 Server Hardware Installation Guide Dimensions Unit: mm Introduction... -
Page 12: Rear Panel Outlets
FASTORA NAST2 Server Hardware Installation Guide Rear Panel Outlets Located at the rear panel of the FASTORA NAST2 server are the I/O outlets for connections of serial and Ethernet interface-supported devices. You could also locate the main power switch and cooling fans. -
Page 13: Chapter 2 Installation Procedures
Preinstallation Checklist In addition to this installation guide, make sure you have the following items, The FASTORA NAS server appliance Power cord Utility CD (including this installation guide) Mounting screws for disk drive and screws used in this appliance for spare Hardware Installation Guide Quick installation guide FASTOR NAS Software User’s Manual... - Page 14 FASTORA NAST2 Server Hardware Installation Guide To install a hard drive to a hot-swappable drive tray Figure 2.1.1.1 螺絲(5X) Figure 2.1.1.2 Installation Procedures...
- Page 15 1. Open HDD door, press plastic locker trigger of tray downward to release tray handle.. See figure 2.1.1.1 2. Remove the empty hot-swappable drive tray by pulling the tray handle. Slide the tray off the tray bay. See figure 2.1.1.1 3.
- Page 16 FASTORA NAST2 Server Hardware Installation Guide Check the hard drive status indicators to verify the drive is operating properly (see the figure 2.1.1.4) 1. When the HDD Yellow LED is continuously on, the drive is failed on not installed. 2. When the HDD Yellow/green LED is off, the hot-swappable drive tray is in bad connection. 3.
-
Page 17: Chapter 3 Starting The Appliance
Complete the installation by switching on the appliance, the power-on diagnostics run automatically. Each time the appliance is switched on; it runs a self-testing program to ensure that it is running correctly. After the power-on diagnostics running, the FASTORA NAST2 server starts to load the application and is ready for use. -
Page 18: Appliance Indicators And Connectors
FASTORA NAST2 Server Hardware Installation Guide 3.2 Appliance Indicators and Connectors The FASTORA NAST2 server has the following indicators of control and connectors. 3.2.1 Power control and reset buttons Power control button 1. When the A/C power cable is in socket, the appliance will start to initiate. Press this button once to shutdown the appliance, and then press once again to switch on the appliance. -
Page 19: Indicators Of System Status Control Led
3.2.3 Indicators of system status control LED Green LED for system status 1. One flash per 0.5 second： when the appliance is booting. 2. One flash per 1.0 second： when the appliance is being shutdown. 3. One flash per 2.0 second： when the appliance is being re-building. Always on：... -
Page 20: Ethernet Port
FASTORA NAST2 Server Hardware Installation Guide 3.2.5 Ethernet Port The FASTORA NAST2 server provides two Ethernet (RJ-45) interfaces. For network connection, just plug in one cable-end of a 100-Base-T into the standard Ethernet phone jack. The pin assignment of the RJ-45 is listed below. RJ-45 Connector Pin Assignment Description Tx+ (Data transmission positive) -
Page 21: Keyboard Port (Internal Use)
3.3.2 Keyboard Port (internal use) The FASTORA NAST2 server provides a keyboard connector for PS/2 type keyboard. Description VCC for Keyboard Keyboard Data Ground for Keyboard Keyboard Clock 3.3.3 CRT VGA Port (internal use) The FASTORA NAST2 server provides a CRT VGA connector for video display. Description Red Signal VGA_GND... - Page 22 This page does not contain any information.
-
Page 23: Appendix A Warning
This is a class A Product. interference in which case the user may be required to take adequate measures. It will be danger if battery is incorrectly replaced. Replacing only with the same or equivalent type is highly recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. - Page 24 This page does not contain any information.
Need help?
Do you have a question about the Fastora NAS T2 and is the answer not in the manual?
Questions and answers