Linkskey LKD-E415 Quick Installation Manual

Quick Installation Guide
Quick Installation Guide
LKD-E415
CAT5 DVI KVM Extender
over LAN w/ Audio&Mic
4 Ports USB 2.0 for Keyboard, Mouse
and High Speed Devices
Full HD 1080p Digital Video up to 100M
Thank you for purchasing the LKD-E415 CAT5 DVI KVM Extender!
With our highly reliable and quality product, users can enjoy
countless benefits from using this CAT5 DVI KVM Extender.
Introduction
The LKD-E415 CAT5 DVI KVM Extender over LAN comprises two
distinct units, the Transmitter (TX) and the Receiver (RX) unit. It
allows fully access and control resources on TX unit from RX
unit over a single standard Cat5 UTP Ethernet cable. The
LKD-E415 is a LAN based DVI KVM Extender that allows user to
access the computer from a remote console anywhere on your
existing local area network infrastructure.
The LKD-E415 CAT5 DVI KVM Extender offers the extension of
keyboard, mouse, digital video, audio, and USB 2.0 devices
distances up to 328 feet (100m) away from your local computer
using a single standard Cat5 UTP Ethernet cable.
The LKD-E415 CAT5 DVI KVM Extender supports digital video
resolution up to 1920 x 1080@60Hz Full HD 1080p through a
maximum of 328 feet single standard Cat5 UTP Ethernet Cable,
while satisfying the optimal video quality. Furthermore, the
LKD-E415 CAT5 DVI KVM Extender supports Graphic Mode and
Video Mode selection to fit your display requirements. Graphic
Mode is optimized for graphic/text display viewing; while Video
Mode is best for dynamically changing video stream playing.
Package Contents
Please check whether you have the following items listed in the
packaging box.
1 x Transmitter (TX) Unit
1 x Receiver (RX) Unit
1 x Video, USB, Audio, and Microphone Integrated Cable
2 x Power Adapter (DC 9V)
1 x Quick Installation Guide
Note: IR Remote Control Unit Pack (Wired Transmitter and
Wired Receiver) is optional and sold separately.
Panels Overview
Transmitter (TX) Unit:
Transmitter Front Panel Overview
TX Front Panel:
a. Reset button (Press and hold for 1 second to completely
power cycle the unit)
b. Red Power LED (Solid: Power is on / OFF: Power is off /
Flashes: Unit initializing)
c. Green Link LED (Solid: Link established / OFF: No link or link
deactivated on TX / Flashes: No digital video signal input,
link not established, or link deactivated on RX)
d. Link Push Button Sw 1 (Toggle between link activate and link
1
Rev. 1.1 Copyright @ All Rights Reserved
LKD-E415 CAT5 DVI KVM Extender over LAN w/ Audio & Mic
deactivate on TX)
e. Mode Push Button Sw 2 (Press and hold for 1 second then
release to toggle between the Video Mode and the Graphic
Mode on both TX and RX units at the same time; Press and
hold for 3 seconds then release to cycle between the
Anti-Dither 1(1bit), 2(2bit), or OFF(off) modes on both TX
and RX units at the same time)
f. RJ45 Ethernet Port (Connect to the RJ45 Ethernet Port on
the remote RX unit directly using a standard Cat5 UTP
Ethernet cable up to 328 feet(100 meters) or via a Gigabit
Ethernet switch)
Transmitter Back Panel Overview
TX Back Panel:
g. Power Jack (DC 9V)
h. USB Type B Port (Connect the USB cable from local
computer)
i. IR Remote Control Port Out (Connect the wired IR Remote
Control Transmitter to local computer, optional)
j. Microphone 3.5mm Jack (Connect the pink microphone
cable to local computer)
k. Audio 3.5mm Jack (Connect the green speaker cable to local
computer)
l. Monitor DVI-I Port Input (Connect the DVI-D video cable
from digital video signal output on local computer)
Transmitter Side Panel Overview
TX Side Panel:
m. Group Address 4-Position Dip Switch (Set the four switches
position to match the Group Address of RX)
Technical Support
E-mail: btitech@linkskey.com
Website: www.linkskey.com