4.1 Instructions, rules and information of the employers’ liability insurance association ....9 4.2 Safety instructions ........................10 4.3 Safety regulations pertaining to the installation of B-TEC machines ..........11 5. Transport and installation ........................12 5.1 Requirements to the installation site ....................12 5.2 Installation ...........................12...
The B-TEC cleaner has been built under highest quality standards for high reliability. Because of certain procedures there are places and parts that can´t be protected without compromising the usability and function.
The B-TEC devices and machines are only allowed to be used for the purpose explicitly described below. Any other use is in contrast with the regulations. The manufacturer cannot be held liable for damages resulting from such non-regulations use.
2. Technical description of the cleaner Starter 01 The universal washer "Starter 01" is produced for automatically cleaning spray paint guns. The automatic wash cycle is activated by a timer. In addition, there is a brush and a fresh solvent jet in the wash enclosure for cleaning objects or spray guns manually.
Page 7
equipment and facility engineering External dimensions Cleaning-room Width: 670 mm Width: 490 mm Depth: 500 mm Depth: 410 mm 370 mm (Cover plate closed) Height: 295 mm Height: 770 mm (Cover plate opened) - Technical changes and errors reserved. All pictures similar - Spray-gun cleaner Starter Page 4...
equipment and facility engineering 2.3 Pneumatic plan and spare parts ordering numbers 020.005.020 045.060.015.005 05.05.05.05 45.40.05 Air connection 10.50.05.20.10 St 10.50.05.30 St. 10.50.15.25 St. M - Throttle valve 05.10.25.10 - Dip-switch 05.40.05.05 Spray-gun cleaner Starter Page 7...
The machines Starter 01 and 02 are classified as machine category 2, group II, machine type explosion group II B and can be used in zone 1. See also machine rating plate: Ex II 2 G c II B < T6 Acids are not permitted.
4. Safety regulations The B-TEC GmbH machines are operationally safe and are constructed according to the state of the art. Due to the nature of the processes there are processes and parts that cannot be protected without impairing operability and functionality.
equipment and facility engineering 4.2 Safety instructions The following persons are not allowed to operate the cleaner: o Women who are pregnant or breastfeeding o Persons with chronic breathing problems and allergic illnesses o Children below 16 years may be employed only under the supervision of a technical expert ...
4.3 Safety regulations pertaining to the installation of B-TEC machines The risk zoning around the cleaning machine and the possible creation of an explosion protection document is, in accordance with legal requirements, the operator´s obligation, because this division is inter alia depending on the solvents used and various conditions such as the ventilation.
Take the machine out of the carton and bring it to the installation site. 5.1 Requirements to the installation site The gun cleaner is build for wall mounting. Optional with a B-TEC stand. Horizontal industrial floor, if the machine shall not be wall mounted. You also can take the B- TEC stand which has the art.-number: 65.40.20...
Page 16
50.20.05 not into exhaust channels of spraying and drying cabinets Attention! Only use original B-TEC waste air hoses. Risk of fire if other hoses are used. Compressed air connection One compressed air connection has to be provided by the plant, depending on the machine: Operating pressure max : 600 kPa (6 bar ;...
Please follow the set-up sequence exactly!! Transport the washer to the installation site as described in chapter 4.3 „Safety regulations pertaining to the installation of B-TEC machines“, connect compressed air supply (maximum 6 bar / 87 p.s.i.) and attach the waste air hose.
Page 18
equipment and facility engineering Operating the automatic washer section ( Starter-01) Open the hinged door. The exhaust system starts automatically. Then install the gun as described below: 1. Remove the lid of spray gun and place it in the lid holder. Make certain that the paint-soiled inner surface faces downwards →...
equipment and facility engineering 6. Close the hinged door from the gun-cleaner. Do not allow the doors or hatches on the machine to fall shut. All machine doors and hatches must be operated with appropriate care and caution by the user. 7.
7.2 Disposal If the machine shall be disposed of, please contact B-TEC or your dealer and request an appropriate quotation or the requirements for proper disposal. The machine must not be disposed of as standard household waste. Depending on the level of contamination, it has to be handled as hazardous waste.
equipment and facility engineering 8. Safety inspection checklist Please make copies before filling out first time! Safety inspections must be conducted at least once every year! | Missing or faulty | Rechecked Item checked 1. Operating instructions 2. Model design label 3.