Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Intelbras IVA 9100 TRI
- Page 1 User manual IVA 9100 TRI...
- Page 2 Congratulations, you have just purchased a product with Intelbras quality and safety. The IVA 9100 TRI sensor is a product of high performance and advanced technology. Equipped with high performance lenses, which provide greater efficiency against unwanted shots, and can be installed indoors, semi-open and outdoors.
- Page 3 » Install the transmitter and receiver so that they are aligned; » LGPD - General Law for the Protection of Personal Data: Intelbras does not access, transfer, capture, or perform any other type of treatment of personal data from this product.
- Page 4 » For the IVA 9100 TRI sensor, follow the protection distances below: Distance between TX and RX 20 m 60 m 100 m 200 M Side Protection Distance (DPL) > 2.5 m > 7.5 m > 12.5 m > 25 M...
-
Page 5: Table Of Contents
Summary 1. Technical specifications 2. Product 3. General characteristics 4. Installation 5. Troubleshooting Warranty term... -
Page 6: Technical Specifications
Passage of the wire 2 digit display Brackets for installation on poles Terminals Con guration DIP Tamper Switches Passage Status LEDs installation screws Lentes Intelbras Adjust vertical alignment Shield Cover xing screw nut Screw Latch adjustment Base horizontal alignment Base Front Cover... -
Page 7: General Characteristics
3. General characteristics The IVA 9100 TRI sensor is a 3-beam active infrared sensor designed for the most adverse scenarios. Several features and functionality have been added to the sensor to provide robustness, the main ones being described below: » High quality optical assembly;... -
Page 8: Installation
1. To identify the Transmitter and Receiver, simply check the label located on the back of the product. Below, the step by step to open the sensor cabinet and perform the installation: Etiqueta de Identifica- Identificação tion Tag IVA 9100 TRI - RECEPTOR Remova o parafuso Remove the screw Remove the front cover as Remova a tampa frontal... - Page 9 2. After identification, run the cable as shown in the following image to connect it to the terminal block: Use the sealing rubber to prevent insects from entering the sensor: Passagem de cabo passage of the cable Borracha de Sealing Rubber vedação Cabo Cable...
- Page 10 4. Connect the wires to the terminals following the guidelines below. » Connect the power to the receiver and transmitter board (12 ~ 24 Vdc / Vac - no polarity); » Connect the wires from the sensor’s alarm output to the zone input of your control panel; »...
-
Page 11: Troubleshooting
8. Align the sensors. The quality of the sensor alignment is identified by the 2-digit display located on the Receiver according to the table below. After aligning, tighten the horizontal adjustment screw. Signal level 95 ~ 99 Great 90 - 94 Good 80-89 Poor... -
Page 12: Warranty Term
8. After its useful life, the product must be delivered to an authorized Intelbras service center or directly disposed of in an environmentally appropriate manner to avoid environmental and health impacts. If you prefer, the battery, as well as other unused Intelbras brand electronics, can be disposed of at any Green Eletron collection point (waste management facility to which we are associated). - Page 13 Support via e-mail: suporte@intelbras.com.br Customer Service: 0800 7042767 Where to buy? Who installs it? 0800 7245115 Imported to Brazil by: Intelbras S/A – Indústria de Telecomunicação Eletrônica Brasileira Rodovia SC 281, km 4,5 – Sertão do Maruim – São José/SC – 88122-001 01.21 CNPJ 82.901.000/0014-41 –...
Need help?
Do you have a question about the IVA 9100 TRI and is the answer not in the manual?
Questions and answers