Table of Contents
Advertisement
Quick Links
Installation manual
Metaloterm
Vlaggen
Land Verhouding
NL
2:3
1:1,5
Installation instructions
United Kingdom
GB
1:2
100 - 400mm Internal Diameter
Twin Wall Insulated Chimney System for wood burning
and multi fuel stoves
BE
13:15 1:1,15
FR
2:3
1:1,5
DE
3:5
1:1,7
CH
1:1
IT
2:3
1:1,5
®
vlag
vlag+outline
MF_install_manual_UnitedKingdom_EN_H
MF
(v.2015)
kleurcodes
C-M -Y-K :
C -M -Y-K:
0-84-77-32
0-0-0-0
C-M -Y-K :
C -M -Y-K:
100-72-0-18.5
0-0-0-0
C-M -Y-K :
C -M -Y-K:
0-0-0-100
0-15-95-0
C-M -Y-K :
C -M -Y-K:
100-70-0-5
0-0-0-0
C-M -Y-K :
C- M -Y- K:
0-0-0-100
0-100-100-0
C-M -Y-K :
C- M -Y- K:
0-100-100-0
0-0-0-0
C-M -Y-K :
C- M -Y- K:
100-0-100-45
0-0-0-0
C- M -Y- K:
76-50-0-46
C- M -Y- K:
0-91-76-6
C- M -Y- K:
0-90-80-5
C- M -Y- K:
0-90-86-0
C- M -Y- K:
0-12-100-5
C-M -Y-K:
0-100-100-0
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Schiedel Metaloterm MF
Summary of Contents for Schiedel Metaloterm MF
- Page 1 Installation manual Metaloterm ® Vlaggen (v.2015) Land Verhouding vlag vlag+outline kleurcodes 1:1,5 Installation instructions C-M -Y-K : C -M -Y-K: C- M -Y- K: 0-84-77-32 0-0-0-0 76-50-0-46 United Kingdom C-M -Y-K : C -M -Y-K: C- M -Y- K: 100 - 400mm Internal Diameter 100-72-0-18.5 0-0-0-0 0-91-76-6...
-
Page 2: Table Of Contents
CONTENTS APPROVAL ��������������������������������������������������������������������������������������������������������������page 3 - Support Components ��������������������������������������������������������������������������������������������page 8 - Chimney Termination DESIGN GUIDE ������������������������������������������������������������������������������������������������������page 4 - Terminals - Mandatory Requirements INSTALLATION INSTRUCTIONS���������������������������������������������������������������������������page 9 PRIOR TO INSTALLATION ������������������������������������������������������������������������������������page 4 - Jointing System - Ventilation - Standard Chimney Sections - Carbon Monoxide Alarms - Individual Components - Painting OFFSET DIMENSIONS ���������������������������������������������������������������������������������������... - Page 3 APPROVAL Metaloterm ® MF is CE Certified to EN1856-1 MPA 0432-CPR-113090037345 with designations: Twin walled stainless steel system with insulation EN 1856-1 T200 P1 W V2 L50040 O10* EN 1856-2 T200 P1 W V2 L50040 O10* EN 1856-1 T200 H1 W V2 L50040 O10* EN 1856-2 T200 H1 W V2 L50040 O10* EN 1856-1 T450 N1 W V2 L50040 O40* EN 1856-2 T450 N1 W V2 L50040 O40*...
-
Page 4: Mandatory Requirements
DESIGN GUIDE Mandatory Requirements Connection to an appliance which is not connected to the fuel supply, should be carried out by a competent person� We recommend the use of HETAS approved installers for solid fuel applications� If installation is carried out by a non HETAS registered installer, the installation must be certified by a local Building Control inspector� Connection to an appliance that is connected to the fuel supply must be carried out by a Gas Safe (Gas) or OFTEC (Oil) registered installer�... -
Page 5: Appliance/Chimney Connection
CONNECTING FLUE PIPE Appliance/Chimney Connection Connection to the appliance can be made using approved single wall connecting flue pipes� This must be done by using the appropriate appliance connector� When a single wall connecting flue pipe is used to connect an appliance to the chimney, the lower end of the chimney section must extend a minimum of 425mm below the ceiling�... -
Page 6: Bs En 15287-1
BS EN 15287-1 BS EN 15287-1 ACCEPTABLE ALTERNATIVE ACCEPTABLE ALTERNATIVE METHODS OF CONNECTION METHODS OF CONNECTION Where a horizontal connecting flue of more than 150mm is required to connect a solid fuel fired appliance to a chimney, Where a horizontal connecting flue of more than 150mm is required to connect a solid fuel fired appliance to a chimney, an installation method as per the examples below may be used provided the following criteria is met:- an installation method as per the examples below may be used provided the following criteria is met:- a) The maximum length of horizontal connecting flue pipe does not exceed 450mm;... -
Page 7: Chimney Diameter
Chimney Chimney (9” x 9”) (9” x 9”) to combustibles Cavity Wall to combustibles Cavity Wall Wall Band Wall Sleeve Wall Sleeve External Masonry Twin Wall Chimney System Trim Collar Chimney System Trim Collar Cavity Wall Cavity Wall Wall Band Wall Sleeve Wall Sleeve External Masonry... -
Page 8: Enclosures/Shafts
Distance to Combustibles In accordance with building regulations, it is essential that the correct distance to combustible material is maintained� On solid fuel applications, where there is a risk of soot fire, a distance of 60mm to combustibles must be maintained within a combustible floor and within a combustible shaft (see Fig�1 below)�There is no need to line the area within the floor cavity with plasterboard;... - Page 9 INSTALLATION INSTRUCTIONS Jointing System All joints in the chimney range, which require a locking band, are made by means of a jointing method� Tis is achieved by pushing together the male and female connections on each and of the main chimney components� In all cases joints should be held securely in place using the locking band, which is supplied with all components�...
- Page 10 Reinforced Locking Band The reinforced locking band, which is purchased separately, is used instead of a standard locking band in a situation where extra structural support is required, for instance where the chimney height is >1�5m above the last support or above the roof� It is also used to provide extra support in long horizontal runs�...
- Page 11 Elbows For offset information on standard elbows, please refer below� In cases of top mounted stoves, a minimum vertical height of 600mm from the appliance is recommended prior to any change of direction in the flue pipe� In all cases the joints should be held securely in place using the locking band� OFFSET DIMENSIONS 15°...
- Page 12 Support Au Plafond Ventilé Geventileerde Verdiepingsondersteuning FIRESTOP COMPONENTS Ventilated Support Plate The support plate is used where the chimney passes through a combustible floor, and the weight of the chimney has to be taken at floor level� The support plate must be firmly fixed by using bolts or screws� For load bearing data refer to page 17� 1�...
- Page 13 Wall Band (50-90mm) Internal and External Application The wall band is supplied in two parts, a stainless steel bands which fits tightly around the outside of the chimney and a stainless steel back bracket� 1� Once the position of the support has been determined, secure the back bracket to the wall with a method of fixing to ensure adequate attachment and support�...
- Page 14 Belüftete Geschoßkonsole Support Au Plafond Ventilé Geventileerde Verdiepingsondersteuning Ceiling Joist Support Where the chimney passes through a combustible ceiling into the roof space, and the weight of the chimney has to be taken at floor level� The ceiling joist support must be firmly fixed by using bolts or screws�...
- Page 15 Angled Flashing Manufactured in stainless steel for use on pitched roofs�This item is used in conjunction with the Metaloterm storm collar, which is purchased separately� The storm collar should be positioned immediately above the cone of the flashing, leaving a gap large enough to allow for ventilation, whilst ensuring that the cone is protected from rain ingress�...
- Page 16 Terminals Anti Splash Raincap Tapered bolt on the locking band clip should be tightened to ensure that the terminal is properly secured to the previous pipe. Terminals are supplied complete with a locking band. Once the terminal has been pushed into place, the adjustment Terminal Terminal bolt on the locking band clip should be tightened to ensure that the terminal is properly secured to the previous pipe.
- Page 17 TYPICAL INSTALLATIONS & LOAD BEARING Mounting heights and distances Ø(mm) 100 130 180 200 250 300 A (m) MFT 45 MFT 87 MFT 90 MFTI MFTR MFTRS MFNL B (m) MFOL1/2 MFOH 2/4 MFSA MFAPO MFAPU MFBTS MFMO MFDQ MFTS C (m) MFDQ MFMB...
- Page 18 OFFSET INSTALLATION Max Offset Info (in same plane) Int Ø 125-200 X (m) Y (m) Example of a design with a double- Finished installation. HEALTH & SAFETY walled connecting flue pipe. HEALTH & SAFETY INSTRUCTION Many building products, including chimney elements are manufactured using natural raw materials which contain proportions of crystaline quartz.
- Page 19 For recommended fuels listings, please refer to the HETAS Guide www�hetas�co�uk In the event of a fault developing in the product due to defective materials or faulty manufacture Schiedel Metaloterm undertake to replace the product only� Schiedel Metaloterm cannot accept liability nor take any responsibility for the installation, building or redecorating costs or any other consequential losses arising�...
- Page 20 Schiedel Metaloterm B.V. Oude Veerseweg 23 4332 SH Middelburg The Netherlands www�metaloterm�com...
Need help?
Do you have a question about the Metaloterm MF and is the answer not in the manual?
Questions and answers