Advertisement
Quick Links
Advertisement
Related Manuals for habitat et jardin 103109
Summary of Contents for habitat et jardin 103109
- Page 2 103109 Control valve Plug seal Plug Pressure gauge Pressure gauge seal M8 connector bolt Gasket Center connecting tube cap Center connecting tube Water distributor Connecting pin Drain tube cap Seal Motor unit Filter sieve Filter cartridge buckle seal Filter cartridge buckle...
- Page 3 List of parts in the package box Optical...
- Page 5 Always follow the basic safety precautions for installation and use of this electrical equipment, including WARNING WARNING: WARNING: WARNING: The product should be away from the water tank, so as to avoid children climbing into it. WARNING: There is risk of electric shock. This product is only connected to the outlet with grounding protection. If it can not be confirmed, please contact an experienced electrician for installation, this outlet has a maximum leakage current of up to 30mA.;...
-
Page 6: Installation Notes
Tools required: 1 slotted screwdriver Product installation location and assembling: The product must be installed on a firm and level surface. Must provide an adequate access, space and light for easy routine maintenance. The motor must be vented and cooled. Do not place the product in damp and poorly ventilated area. It is recommended that there are at least two persons for the product installation. - Page 7 Step I Before filling the sand, connect the central connecting tube (9) and the water distributor (10) as shown in Fig. 03, align the connecting pin on A position with the big gap on water distributor B position, and press the water distributor into place in the arrow direction (as shown in Fig. 04, if the water distributor hook is connected to the endface of the center connecting tube, it is assembled in place), and then place the assembled water distributor components into the body, as shown in Fig.
- Page 8 Control valve unit installation: Fig. 09 Fig. 10 Fig. 11 Groove Step I Step II Thoroughly clean the sand and As shown in Figs 10 and 11, align the center hole (A) of the impurities in the groove, and control valve unit sand shield cover with the outer circle (B) of place slowly the upper cover the center connecting tube, Cover the gap of the control valve seal (24) into the groove.
- Page 9 Step III As shown in Figs12 and 13, remove M8 adjustment bolt, washer and M8 quadrilateral nut (6, 7, 25) from the hoop, install the hoop around the flange between the body and the control valve unit, install M8 adjustment bolt and washer into the M8 quadrilateral nut hole of the hoop, clockwise tighten them with a slotted or Phillips screwdriver (not provided with the product);...
- Page 10 Step V As shown in Figs 16 and 17, connect 38 bellows (23) between the control valve B port and the motor B port, and tighten 32-50 hoop (21) with a flathead screwdriver. Sand filter pump and water pool installation: Fig.
-
Page 11: Operation Steps
It is drained directly from the It is drained directly from the sewage sewage discharge outlet, WASTE discharge outlet, to reduce the water level or without flowing through the drain the water in the tank filter layer The water flows directly into the water tank via the water It is the water in water circulation tank, RECIRCULATE... - Page 12 them together in C position, connect the other end of the tube to the water pool E position, and lock it with the hose clamp. (See Fig. 18) 6.Install the plug (3) on D position. (See Fig. 18) 7.Turn on the power supply and select the desired position for operation. Note: Do not set the control valve between the two functions, otherwise it will cause leakage.
- Page 13 Sand filter pump operations 1. After the preparations are completed, the sand filter pump can be used. Set the filtering performance of the control valve. 2. Insert the plug into the appropriate outlet to operate the sand filter pump. Note: During the sand filter pump operation, check the pressure gauge (4); that the pointer is within the green range indicates a normal operation.
- Page 14 Before the water tank is drained or leveled, must ensure that the drainage direction towards the drainage ditch and is away from the building. For special requirements about water treatment, please see the local regulatory requirements. 2.Turn off the product switch and unplug the power plug. 3.
-
Page 15: Product Specifications
(In case of doubt on the pump or any circulation devices, please contact After Sales Service directly, co ntact details in the following affix. the address or telephone number where the consumer/installer can obtain additional information during the installation in the event of problems.) Product specifications Model 103109 BC002A Voltage 220-240V Power Maximum operating <0.2bar (3psi) - Page 16 Responsable de la commercialisation du produit / Company in charge of commercializing the product / Responsable de la comercialización del producto / Responsabile della commercializzazione del prodotto: GECODIS SA 32, rue de paradis 75010, Paris, France Service commercial/ Commercial service/ Servicio comercial / Servizio commerciale : Habitatetjardin.com 32, rue de paradis 75010, Paris, France...