Beha-Amprobe AT-8000-EUR Quick Start Manual

Beha-Amprobe AT-8000-EUR Quick Start Manual

Advanced wire tracer
Hide thumbs Also See for AT-8000-EUR:

Advertisement

Quick Links

Quick Start Guide
AT-8000-EUR Advanced Wire Tracer
Reliable, precise
breaker/fuse identification
Tested by Fluke and safety
certified by 3rd party labs
ENG GER
ITA
FRE
SWE FIN POR NOR DAN CZE
AT-8000-RE
RECEIVER
Intuitive Transmitter
automatically senses whether
the system is energized or
de-energized
Most accurate wire tracing
in its class with 10
sensitivity modes
SPA DUT POL
AT-8000-TE
TRANSMITTER
HI
LO

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AT-8000-EUR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Beha-Amprobe AT-8000-EUR

  • Page 1 Quick Start Guide AT-8000-EUR Advanced Wire Tracer Reliable, precise Intuitive Transmitter breaker/fuse identification automatically senses whether the system is energized or Tested by Fluke and safety de-energized certified by 3rd party labs Most accurate wire tracing in its class with 10...
  • Page 2 AT-8000-EUR Advanced Wire Tracer...
  • Page 3: Table Of Contents

    • CT-400-EUR signal clamp (optional accessory) to improve accuracy and performance when there is no access to bare conductors See the user manual for further instructions regarding special applications. ® ©2020 Beha-Amprobe For detailed specifications and ordering go to beha-amprobe.com 6012405 B...
  • Page 4: Tracing Energized Wires - Smart Sensor Tm

    AT-8000-EUR Tracing Energized Wires - Smart Sensor Set-up: Receiver: Test Leads Energized Smart Sensor Mode The Smart Sensor enables easier wire tracing by showing the direction and position of the wire and is the recommended method for tracing Energized wires.
  • Page 5: Tracing Energized And De-Energized Wires - Tip Sensor

    30 V AC/DC, and it should be off for De-energized circuits below 30 V AC/DC. 3. Select HIGH signal mode by pressing HI. Aligning the Tip Sensor with the wire ©2020 Beha-Amprobe ® For detailed specifications and ordering go to beha-amprobe.com 6012405 B...
  • Page 6: Connecting Transmitter To An Energized Working System

    AT-8000-EUR Connecting Transmitter to an Energized Working System The Transmitter, with the red test lead, can be directly connected to the live wire of the working electrical equipment under load (motor, electronics, etc). Tracing can be performed without needing to turn off the equipment or switching power off.
  • Page 7: Identifying Energized And De-Energized Breakers And Fuses

    3. Press ENTER when complete to return to the next breaker/fuse. The order of scanning the home screen. does not matter. You can scan breakers/fuses multiple times. The Receiver records the highest detected signal. ©2020 Beha-Amprobe ® For detailed specifications and ordering go to beha-amprobe.com 6012405 B...
  • Page 8: Ncv Mode

    AT-8000-EUR NCV Mode Receiver: NCV Mode The NCV (Non-Contact Voltage) mode is used to verify that a wire is Energized. This method does not require the use of the Transmitter. The Receiver will detect an Energized cable if the voltage is between 90 V and 600 V AC and between 40 Hz and 400 Hz.
  • Page 9: Finding Breaks And Opens

    Note: For best results, ground all De-energized wires that run in parallel with the black test lead. ©2020 Beha-Amprobe ® For detailed specifications and ordering go to beha-amprobe.com 6012405 B...
  • Page 10: Finding Shorts

    AT-8000-EUR Finding Shorts AT-8000-T TRANSMITTER Set-up: Set-up: Transmitter Receiver BLINKING AT-8000-RE Transmitter indicator showing RECEIVER signal in Loop mode 1. Turn on the Receiver and perform tracing in Energized TIP SENSOR mode. 1. Turn on the Transmitter. 2. Verify that the test leads are properly connected;...
  • Page 11: Wire Tracer Specifications

    (7.2 x 3.66 x 1.97 in) (5.9 x 2.75 x 1.18 in) Weight (batteries installed) Approx. 0.544 kg (1.20 lb) Approx. 0.57 kg (1.25 lb) Approx. 0.114 kg (0.25 lb) Certifications ©2020 Beha-Amprobe ® For detailed specifications and ordering go to beha-amprobe.com 6012405 B...
  • Page 12: Accessory Specifications And Included In Wire Tracer Kits

    AT-8000-EUR Accessory Specifications ADPTR-SCT TL-8000-EUR CAT IV 600 V (test leads) Measurement Category CAT II CAT IV 600 V (alligator clips) CAT II 1000V (test probes) 600 V, 10 A max. (red/black leads) 600 V, 6 A max. (green lead) Operating Voltage and Current 102 to 253 V AC, 4 A max.
  • Page 13 Advanced Wire Tracer - Quick Guide ©2020 Beha-Amprobe ® For detailed specifications and ordering go to beha-amprobe.com 6012405 B...
  • Page 14 In den Engematten 14 79286 Glottertal, Germany Tel. +49 (0) 7684 - 8009-0 info@beha-amprobe.de beha-amprobe.de Science Park Eindhoven 5110 NL-5692 EC Son The Netherlands Tel. +31 (0) 40 267 51 00 beha-amprobe.com 52 Hurricane Way NR6 6 JB United Kingdom e-mail: info@beha-amprobe.co.uk beha-amprobe.com...

Table of Contents