Table of Contents
Advertisement
Quick Links
MBUS-REP - USER MANUAL
MBUS-REP
R
EPEATER FOR THE
M-B
US
Version 1.2
Date: 2019-05-21
Author:
Sven Ladegast
solvimus GmbH
Ratsteichstr. 5
98693 Ilmenau
Germany
solvimus GmbH – Ratsteichstr. 5 – 98693 Ilmenau – Germany
Phone: +49 3677 7613060 – Fax: +49 3677 7613069 – Email: info@solvimus.de
...we solve.
www.solvimus.de
Advertisement
Table of Contents
Related Manuals for Solvimus MBUS-REP
Summary of Contents for Solvimus MBUS-REP
- Page 1 EPEATER FOR THE Version 1.2 Date: 2019-05-21 Author: Sven Ladegast solvimus GmbH Ratsteichstr. 5 98693 Ilmenau Germany solvimus GmbH – Ratsteichstr. 5 – 98693 Ilmenau – Germany Phone: +49 3677 7613060 – Fax: +49 3677 7613069 – Email: info@solvimus.de ...we solve. www.solvimus.de...
- Page 2 MBUS-REP - User manual This page is left blank intentionally. Page 2/11 Version 1.2 Sven Ladegast, 2019-05-21 MBUS_REP500_UG_1.2_EN.docx Released © solvimus GmbH...
-
Page 3: Table Of Contents
MBUS-REP - User manual Contents General hints and conventions ............................ 4 About this document ............................. 4 Legal bases ................................. 4 1.2.1 Copyright ................................4 1.2.2 Personnel qualifications ..........................4 1.2.3 Technical condition of specified devices .................... 4 Symbols ..................................4 Font conventions .............................. -
Page 4: General Hints And Conventions
The solvimus GmbH will be exempted from any liability in case of changes in hardware or software as well as to non-compliant usage of components. -
Page 5: Font Conventions
MBUS-REP - User manual Additional information: References to additional literature, manuals, data sheets and internet pages. 1.4 Font conventions Names of paths and data files are marked in italic-type. According to the system, Slashes or Backslashes are used. D:\Data\ i.e.: Menu items are marked in italic-type, bold letters. -
Page 6: Scope
It is necessary to provide good grounding to personnel, working environment and packing. Electroconductive parts and contacts should not be touched. 1.7 Scope This manual describes the devices mentioned in the title, supplied by solvimus GmbH, Ilmenau. 1.8 Abbreviations Abbreviation Description Deutsches Institut für Normung, German standardization body... -
Page 7: General Information
For connecting it to other systems a translation is necessary. The MBUS-Rep acts as an M-Bus master as well as an M-Bus slave. It is fully transparent to the baud rate that is used on the M-Bus and on-the-fly baud rate changes are supported by the device. By the use of the MBUS-REP it is possible to extend an existing M-Bus with further units sharing the same M-Bus installation. -
Page 8: Connectors
Not connected Cross sectional area 2,5 mm² Table 1: Connectors 2.3 State LEDs The MBUS-REP is equipped with 3 state LEDs. These LEDs visualize the operational state of the device: Color Description Lights up when a collision has been detected on the M-Bus... -
Page 9: Bringing Into Service
The new M-Bus segment shall be connected to the terminals MBUS+ and MBUS- (see section 2.2). The MBUS-REP is able to supply this new bus segment with 125 or 500 UL respectively by only drawing 2 UL from the M-Bus on its slave connectors (MBI1 & MBI2). -
Page 10: Troubleshooting
MBUS-REP - User manual 4 Troubleshooting In case the MBUS-REP works not as described in this document, it is useful to locate the malfunction in order to resolve the issue and to recover the full functionality again. 4.1 Hardware error 4.1.1 The devices does not respond... -
Page 11: Technical Data
• Safety: Bipolar M-Bus slave terminals, Reverse voltage protection, over-voltage protection (transient) 5.2.2 Communication interfaces The MBUS-REP comes with an M-Bus slave interface and an M-Bus master interface (see pin assignment at section 2.2) • Conform to EN 13757-2/-3 •...
Need help?
Do you have a question about the MBUS-REP and is the answer not in the manual?
Questions and answers