Do you have a question about the STRIP LED 12V and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for Quick STRIP LED 12V
Page 1
STRISCE LED STRIP LED REV 001 STRIP LED 12V COLLEGAMENTO ED ISTRUZIONI PER IL TAGLIO Manuale d’uso WIRING AND CUT INSTRUCTIONS Manual of use PRECAUZIONI ED AVVERTENZE - CAUTIONS AND WARNING LA MESSA IN FUNZIONE E LA MANUTENZIONE DELL’APPARECCHIATURA DEVE ESSERE EFFETTUATA DA PERSONALE QUALIFICATO.
Page 3
STRIP LED 12V - REV001B INDICE Pag. 4 INSTALLAZIONE: istruzioni per il taglio Pag. 5 INSTALLAZIONE: cappuccio alimentazione, cappuccio finale, driver Pag. 6 SCHEMA DI COLLEGAMENTO / CARATTERISTICHE Pag. 7 ESEMPI APPLICATIVI INDEX Pag. 8 INSTALLATION: cut instructions Pag. 9 INSTALLATION: power cap - ending cap - driver Pag.
Page 4
12V. ® Quick S.p.A. non si assume alcuna responsabilità in caso di errato collegamento e/o errato utilizzo di questo apparecchio. PRIMA DI UTILIZZARE LA STRIP LED, LEGGERE ATTENTAMENTE IL PRESENTE MANUALE D'USO.
CAPPUCCIO FINALE garantiscono CAPPUCCIO il grado FINALE STRIP LED Eventuali DRIVER STRIP LED e CAPPUCCI DI CHIUSURA necessari alla personalizzazione della STRIP LED 12V non sono inclusi nella confezione. Contattare Quick facendo riferimento ai codici: ® DRIVER STRIP LED KCAD20SLSUP0...
Page 6
SCHEMA DI COLLEGAMENTO / CARATTERISTICHE STRIP LED 12V - REV001B SCHEMA DI COLLEGAMENTO STRIP LED 12V con DRIVER STRIP LED DRIVER STRIP LED nero NEG 12/24 rosso POS RISPETTARE LE POLARITÀ. ATTENZIONE: la parte con i cavi più corti va collegata alla STRIP LED, la parte con i cavi più lunghi va collegata all’alimentazione.
La necessità di collegare più di 5 metri di STRIP LED 12V, in questo esempio 15 metri, rende necessario l’impiego di altri 2 DRIVER STRIP LED. Viene collegato un pezzo da 5 metri di STRIP LED 12V ad un DRIVER STRIP LED, 2 pezzi da 2,5 metri ad un...
Page 8
ALWAYS RESPECT POLARITY AS SHOWN IN THE PRODUCT LABEL: RED WIRE CONNECTED TO POSITIVE POLE AND BLACK WIRE CONNECTED TO THE NEGATIVE POLE. Quick STRIP LED 12V can be cut approximately every 5 centimeters between the two pairs of copper dots that occur ® after every three LEDs.
CAP guarantee the RATING ENDING CAP STRIP LED Any additional STRIP LED DRIVER and CAPS needed to personalize the installation of STRIP LED 12V are not included in the packaging. Contact Quick making reference to the following part numbers: ®...
WIRING DIAGRAM / CHARACTERISTICS STRIP LED 12V - REV001B WIRING DIAGRAM STRIP LED 12V with DRIVER STRIP LED DRIVER STRIP LED black NEG 12 VDC red POS RESPECT POLARITY. ATTENTION: the side with shorter wires goes to Strip LED, the side with longer wires goes to Power Supply.
Page 11
EXAMPLE 3 The need to connect more than 5 meters of STRIP LED 12V, in this example of 15 meters, makes the use of two more STRIP LED DRIVERS necessary. They are connected by the 5 meters of STRIP LED 12V and a STRIP LED DRIVER, two 2.5 meter pieces to the second STRIP LED DRIVER and five 1 meter pieces to the third STRIP LED DRIVER.
Page 12
STRIP LED 12V R001 Codice e numero seriale del prodotto Product code and serial number QUICK S.p.A. - Via Piangipane, 120/A - 48124 Piangipane (RA) - ITALY ® Tel. +39.0544.415061 - Fax +39.0544.415047 www.quickitaly.com www.quickmarinelighting - www.quicklighting.com...
Need help?
Do you have a question about the STRIP LED 12V and is the answer not in the manual?
Questions and answers