RAIMONDI BERTA ADV Manual
  1. Manuals
  2. Brands
  3. RAIMONDI Manuals
  4. Cleaning Equipment
  5. BERTA ADV
  6. Manual

RAIMONDI BERTA ADV Manual

Electrosponge
Hide thumbs
Table of Contents

Advertisement

Quick Links

GB

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BERTA ADV and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for RAIMONDI BERTA ADV

  • Page 3: Table Of Contents

    ENGLISH BERTA ADV ELECTROSPONGE CE DECLARATION OF CONFORMITY Raimondi S.p.A. hereby declares that the “BERTA” electrosponge fulfils the essential requirements of the following Directives: EC Directive 98/37 (Machine Directive) EEC Directive 73/23/ (Low Voltage Directive). RAIMONDI S.p.A. Via dei Tipografi, 11...

  • Page 4: Use

    Before using the machine, read this manual carefully in order to prevent accidents and malfunction- ing. The “BERTA ADV” electrosponge has been designed to clean floors during the grouting of floor tiles. The machine cleans away excess grout and epoxy sealant, whilst smoothing the joints between tiles.

  • Page 5: Transport

    ENGLISH BERTA ADV ELECTROSPONGE Transport Wind up loose power cables, without knots or kinks. Never lift or carry the machine by the power supply cable. Never disconnect the machine by pulling the power supply cable. Never transport the machine while it is still plugged in.

  • Page 6: Preparing The Machine

    BERTA ADV ELECTROSPONGE ENGLISH Preparing the machine Before using the machine to clean a floor, moisten the sponge. Fill the tank with about 15 litres of cold and clean water. Shift the lever (A) to its upright position (figure 2).

  • Page 7: Dosing Water In The Sponge Roller

    ENGLISH BERTA ADV ELECTROSPONGE Dosing water in the sponge roller To increase or reduce the moisture content of the sponge roller, proceed as follows: - shift the lever (A) to its upright position (figure 2 - page 6) - raise the stopping spring (B - figure 5) and remove it;...

  • Page 8: Replacing The Sponge Roller

    BERTA ADV ELECTROSPONGE ENGLISH Replacing the sponge roller BEFORE PERFORMING ANY OPERATION, MAKE SURE THAT THE MACHINE IS UN- PLUGGED. REMOVING THE SPONGE ROLLER Shift the lever (A) to its upright position (figure 2 – page 6). Move to the side opposite the motor casing.

  • Page 9: Cleaning The Tank

    ENGLISH BERTA ADV ELECTROSPONGE Cleaning the tank BEFORE PERFORMING ANY OPERATION, MAKE SURE THAT THE MACHINE IS UN- PLUGGED. Shift the lever (A) to its upright position (figure 2 – page 6). Raise the water conveyor belt and remove the tank (figure 11).

  • Page 10: Replacing The Water Sealing Plugs

    BERTA ADV ELECTROSPONGE ENGLISH Replacing the water sealing plugs Shift the lever (A) to its upright position (figure 2 – page. 6). Remove the sponge roller (see “Removing the sponge roller” on page 8). Remove worn rubber plugs (L – figure 12) by loosening the fix- ing screws.
  • Page 11 ENGLISH BERTA ADV ELECTROSPONGE BERTA...
  • Page 12 BERTA ADV ELECTROSPONGE ENGLISH...
  • Page 13 ENGLISH BERTA ADV ELECTROSPONGE BERTA ADV POS. PRODUCT CODE PART NAME POS. PRODUCT CODE PART NAME STARTER SPARE PARTS 128LE02D ROLLER PRESSURE ADJUSTMENT LEVER 128TI01A TIE-ROD FOR BUMPER ADJUSTMENT 235ES01A STARTER WITH CE PLUG (230V/50HZ) 128TI02A TIE-ROD FOR SQUEEZER ADJUSTMENT...
  • Page 14 BERTA ADV ELECTROSPONGE ENGLISH...
  • Page 15 BERTA ADV BERTA ADV Date of production Serial n° RAIMONDI S.p.A. MODENA 2005 designed by TECNO DINAMICA S.n.c.

Table of Contents

Save PDF