Advertisement
Table of Contents
User Manual & Operating Instructions
22.9in.( 582mm) L × 6.9in.( 175mm) W × 8.94in.( 227mm) H
This winch is equipped with a series wound motor and is designed for intermittent duty
general use. This winch is not to be used for industrial lifting or moving people.
Improper operation could damage the winch and void the warranty.
Free spool clutch is operated by a pull and turn knob, which disengages the gearbox,
allowing the cable to be released.
www.tractorsupply.com
10000lb.Winch
Performance Specifications
Max Line Pull
10000lbs.(4536kgs)
Gear reduction ratio
Series wound DC12V motor with 2.8hp output
Overall Dimensions
Drum size
2.48in.( 63mm) D × 8.54in.( 217mm) L
Remote Controller
Max control distance 30m
82ft.(25.0m) L of 25/64in.(10mm) D
Net weight
69.7lbs.(31.6kgs)
Product Overview
Tractor Supply Company ○
For customer support call 1-888-376-9601
253:1
Motor
Rope
R
0
0
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Tractor Supply Traveller X
- Page 1 Improper operation could damage the winch and void the warranty. Free spool clutch is operated by a pull and turn knob, which disengages the gearbox, allowing the cable to be released. Tractor Supply Company ○ www.tractorsupply.com For customer support call 1-888-376-9601...
- Page 2 INSTALLATION Correct installation of the winch is required for proper operation. (M10×1.5×35mm), M10 nut, ∅10 flat washer and ∅10 spring washer (four sets). Mount the winch on the vehicle or other fixed installation by using a screw WARNING: This winch must be mounted with the cable in an under wound direction. Improper mounting could damage the winch and void the warranty.
- Page 3 OPERATION Pull and turn the clutch knob, so the drum can turn freely by hand. Use hand saver bar to hitch the hook of the cable assembly and pull cable to the load. Attach the cable hook to the load. WARNING: Check that there are at least five turns of cable remaining on the drum before operation.
- Page 4 TROUBLE SHOOTING SYMPTOM POSSIBLE CAUSE SUGGESTED ACTION -Switch Assembly not -Insert switch assembly all the way into the connected properly connector. -Loose battery cable -Tighten nuts on all cable connections. connections Motor does not -Defective switch -Replace switch assembly. turn on assembly -Check voltage at armature port while switch -Defective motor...
- Page 5 WINCH ASSEMBLY www.tractorsupply.com For customer support call 1-888-376-9601...
- Page 6 WINCH PART LIST Part # Description VT1000100 Motor Assembly VT1000001 Cap Screw M10 x 35 VT1000002 Lock Washer Φ10 VT1000003 Think Flat Washer Φ10 VT1000004 Hex Nut M10 VT1000005 Bushing—Drum VT1000006 Ring Seals VT1000007 Tie Bar VT1000008 Cap Screw M8 x 30 VT1000009 Lock Washer Φ8 VT1000011...
- Page 7 SAFETY PRECAUTIONS Never lift people or hoist loads over people. Do not lift items vertically, this winch is designed for horizontal use only. Never overload. Be sure all equipment used meets the winch’s maximum line pull rating. When double-lining, pulley blocks should be rated for a minimum of two times the winch’s line pull rating.
- Page 8 Total rope on the drum ft (m) 10000(4536) 17.4(5.3) 7848(3560) 39.4(12.0) 6459(2930) 65.0(19.8) 5487(2489) 82.0(25.0) Distributed By: TRACTOR SUPPLY COMPANY 5401 VIRGINIA WAY, BRENTWOOD, TN37027 For customer support, call:1-888-376-9601 www.TractorSupply.com MADE IN CHINA Tractor Supply Company ○ www.tractorsupply.com For customer support call 1-888-376-9601...
Need help?
Do you have a question about the Traveller X and is the answer not in the manual?
Questions and answers
Hi can you tell me what model winch i have #2008104322
The winch model associated with Tractor Supply part number Traveller X #2008104322 is a 10000 lb. winch with the following specifications:
- Max Line Pull: 10,000 lbs (4536 kgs)
- Gear Reduction Ratio: 253:1
- Motor: Series wound DC 12V motor with 2.8 hp output
- Rope: 82 ft (25.0 m) of 25/64 in (10 mm) diameter
- Remote Control: Max control distance of 30 m
- Net Weight: 69.7 lbs (31.6 kgs)
- Dimensions: 22.9 in L × 6.9 in W × 8.94 in H
- Drum Size: 2.48 in D × 8.54 in L
It is intended for intermittent duty general use and not for industrial lifting or moving people.
This answer is automatically generated