Sony TRINITRON KV-32XBR450 Service Manual page 6

DX1A-2001&2000 SERVICE LIST (#1):
Register
No. & Name
SNNR Setting-based Control Table for YHCO & YHCG
20 YHCO Y output high frequency component coring
21 YHCG Y output high frequency component coring gain
22 HSSL Hsync slice level
23 VSSL Vsync slice level
24 ADCL ADC clock delay
NRMD Setting-based Control Table for D2GA
25 D2GA Moving detection gain
26 KILR Killer detection reference
Option1:
27 OP1
Selection of comb filter & recursive noise reduction types
28 NR1 Noise reduction on/off
29 NR2 SNNR control on/off
30 WSL Noise level detection data
31 HPLL H-PLL filter (Must be set to 1 when MN signal is input.)
32 BPLL Burst PLL filter
33 FSCF Burst extraction gain
34 PLLF PLL loop gain
35 CC3N Selection of a line-comb filter C separation filter characteristic
36 HDP Fine adjustment of the system H-phase
Internal burst gate start position
37 BGPS
{Gate Start Position from Hsync center = 0.25 x BGPS + 2
Internal burst gate width
38 BGPW
{Gate Width = 0.25 x BGPW + 0.5 (ms)}
39 TEST Test bit {0: Normal mode, 1: Test mode (forbidden setting)} C
40 WSC Amount of noise detection coring
41 LIND DRC-M line-doubling setting for non-standard signals
42 PFGO (YPFG offset at GR on) --- Not used for DX1A
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
Register
No & Name
CVideo2
#28 NR1 (cont.) 0
Note: The same 3D-COMB service data is used for DX1A-2001&2000.
Control Register
Function & Link
DX1A-2001&2000 SERVICE LIST (#1):
Data Initial/Average Setting
(32V&36V CRTs)
SVideo2 CVideo3 SVideo3
1 0 1
3D-COMB / mPD64082
Data Data
Data Initial/Average Setting
Type Range (32V&36V CRTs)
SNNR = 0 SNNR = 1
0~3 1 1
0, 1 0 0
C 0~15 12 C: Common data
C 0~15 8
C 0~3 3
NRMD = 0 NRMD = 1
0~7 4 4
C 0~15 3
C 0, 1 1
UHF/VHF CVideo1
0, 1 0 0
C 0, 1 0
0~255 1 Byte Data from Read Register WSL
C 0, 1 1
C 0, 1 1
C 0, 1 0
C 0, 1 1
UHF/VHF Video1~4
0, 1 0 0
C 0~7 5
C 0~15 4
C 0~15 10
0, 1 0
C 0~3 1
UHF/VHF & Video1~4
0~63 0
Micro
(Not used for DX1A)
--- 0~7 3
3D-COMB / mPD64082
Comment
— 22 —
KV-32HS20/36HS20/36HS20H/32XBR450/36XBR450/36XBR450H
(Part-3/4)
Comment
SNNR = 2 SNNR = 3 (Not SNNR Offset Data)
1 1
YHCO&YHCG settings are sent
directly to 3D-Comb device.
0 0
NRMD = 2 NRMD = 3
4 4
SVideo1 This setting continues to
the next page.
1
Video5&6 Video1~4: CVideo1~4 & SVideo1~3 inputs
Video5&6: YPbPr-480i/480p/1080i inputs
0
Video5&6 This setting is used for non-standard signals
2 such as Play Station signals.
(Part-4/4)