SmarLink FW50 User Manual

3g/4g industrial router

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

3G/4G Industrial Router

FW50 User Manual

Table of Contents

Need help?

Do you have a question about the FW50 and is the answer not in the manual?

Questions and answers

Summary of Contents for SmarLink FW50

Page 1 3G/4G Industrial Router FW50 User Manual...
Page 2: Table Of Contents
Table of Contents I、Device Connnection ..........................3 II、Device Login ............................4 III、Device Settings ..........................5 IV、Setup Wizard ............................5 V、Work Mode ............................... 8 VI、Running State ........................... 12 1. Network State ..........................12 2. LTE State ............................13 3. DHCP List ............................13 4.
Page 3: I、Device Connnection
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com Ⅰ. Device Connection When users get a router, first use the pin to stick the small yellow dot next to the SIM card slot to popup the card slot and install the SIM card, and then install the six antennas (5.8g*2,2.4g*2,4g*2) corresponding to the antenna logo and the silkscreen logo on the antenna port of the device.
Page 4: Setup Wizard
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com admin (lowercase). After logging in, users can enter the router’s management interface. Ⅲ. Device Setting After logging in to the router management interface, users can see such information as SIM card status and signal strength, firmware version, system language and networking information. Ⅳ.
Page 5 Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com When users enter the APN configuration, the system has its own default settings of most operators and it can be automatically selected according to the attribution of the SIM card. And users can usually choose the deactivate default and do not need to reset.
Page 6: Work Mode
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com The LAN IP address can be set according to the requirements. The default address is 192.168.5.1. Note that if users modify it, users need to use the new IP to log in to the management page after completing the setup wizard.
Page 7 Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com “3G/4G”. Users can select different work modes according to different usage scenarios to achieve high efficiency and precision and maximize the use of our device. “Wire break detection” is a function that is only available in 3G/4G mode.
Page 8 Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com...
Page 9 Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com...
Page 10 Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com...
Page 11 Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com...
Page 12: Running State
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com Ⅵ. Running State 1.Network State The network state can display the system information of the router, networking information, VPN information (the VPN information will only be displayed after the router successfully connects to the VPN), and the running state, etc.
Page 13: Lte State
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com 2. LTE State Display the model, network type, operator, etc. of the 4G module. 3.DHCP List Users can view information about all devices connected to the router; including host name, IP address, MAC address, device operating system, lease time, etc.
Page 14: Data Statistics
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com 4. Data Statistics Display the use condition of router’s hardware. Ⅶ. LTE Settings 1. APN Setting APN refers to a network access technology, which is a parameter that must be configured when accessing the Internet through a mobile phone. It determines which access method the mobile phone uses to access the network.
Page 15: Network Settings
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com 2. Network Mode The network mode is divided into automatic selection and manual setting. The system defaults to automatic selection. Generally, it can be automatically selected without special circumstances. Only when the network type supported by the SIM card does not match, is manual setting required. Ⅷ.
Page 16: Lan Setting
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com with other IP addresses. PPPOE refers that connect to the WAN port of the machine by the network cable, and the other end is connected to the network port of the optical modem, and then the device can perform related settings to access the Internet.
Page 17: Vpn Setting
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com Ⅸ. VPN Setting The function of the virtual private network is to establish a private network on the public network for encrypted communication. VPN is widely used in enterprise networks. VPN gateway implements remote access by encrypting the data packet and converting the destination address of the data packet.
Page 18: Basic Setting
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com Ⅹ. Wireless Settings Instructions for 2.4G (Same Wireless Settings for 5.8G) 1. Basic Setting In basic setting, you can modify the name and password of WIFI, hide WIFI, modify channel, 2. Wireless Relay Through wireless relay, it can be connected to the upper-level router WIFI for networking.
Page 19: Wireless Client List
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com 4. Wireless Client List There will display the information of the device connected to the router through wireless, and users can view the MAC address of the device. Ⅺ. QoS 1. QoS Rules QoS can limit the upload and download speed of devices connected to the router.
Page 20: Port Forwarding
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com rules, etc. 2. Port Forwarding Port forwarding refers to port mapping. Port mapping is to map a port of the IP address of the intranet host to the external network, so that the external network can access to the host to provide corresponding services.
Page 21: Dmz Host
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com 3.DMZ Host DMZ is the abbreviation of “demilitarized zone” in English, and the Chinese name is “Geli Qu”, also called as “Fei Junshihua Qu”. It is to solve the problem that the access user of the external network cannot access to the internal network server after installing the firewall, and it’s a buffer between the non-secure system and the security system.
Page 22: Serial Port Service
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com XIII. Serial Port Service Serial communication port, refers to as serial port. The serial port on the microcomputer is usually 9-pin, also has 25-pin interface, with the maximum speed of 115200 bps. It is usually used to connect a mouse (serial port) and communication equipment (such as connecting an external modem for data communication or some factory CNC machine interface).
Page 23: Multimedia
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com XIV. Multimedia 1.File Sharing Users can choose whether to start the SAMBA server. Samba server is a free software that implements the SMB protocol on Linux and UNIX systems, consisting of a server and a client program. SMB (Server Messages Block) is a communication protocol for sharing files and printers on a local area network.
Page 24: Administrator Setting
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com XV. Device Management 1. Administrator Setting In the administrator setting, users can modify the login account and password of the router’s background management, set the time zone and time, and set the dynamic domain name.
Page 25 Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com 2. Remote Management After setting up remote management, users can log in to the router’s background management page through remote login. When setting remote management, the IP of WAN port must be public network IP. Users can access to page through entering WAN port IP+ port in browser address bar.
Page 26 Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com 3. Firmware Upgrade In firmware upgrade setting, the firmware of the router can be updated to the latest version. 4. Device Management Users can import or export the router’s configuration information and restore the router to the factory settings.
Page 27: System Restart
Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com 5. System Restart In system restart setting, users can restart the router and customize the router to automatically restart the time.
Page 28 Shenzhen Newchiba smartlink Technology Co., Ltd. www.newchiba.com...