Advertisement
Quick Links
Items included:
7 x Acrylic cutouts labeled A-G
1 x Acrylic IO Panel
1 x Acrylic locking plate of PCI cards
2 x Acrylic 5.25 spacers
2 x momentary switches (power/reset)
2 x blue tailed LED w/chrome bezels
1 x stainless steel handle w/2 mounting screws
6 x PCI cover plates
1 x bag of motherboard mounting hardware (10 standoffs, 10 screws)
1 x bag of left sided acrylic blocks (10 pcs – labeled "L")
1 x bag of right sided acrylic blocks (10 pcs – labeled "R")
1 x bag of long 3mm screws (60 pcs)
1 x bag of long 6/32 screws (16 pcs)
1 x bag of long fan screws (8 pcs)
Assembly:
Find the acrylic cutout labeled "A" on one side. This is the bottom of the case. On one side protective
film will need to be removed from the acrylic while the other side will already have the film removed and
4 long sled like feet adhered to the plate.
BOB SLAY
(assembly instructions)
Advertisement
Related Manuals for Mountain Mods BOB SLAY
Summary of Contents for Mountain Mods BOB SLAY
- Page 1 BOB SLAY (assembly instructions) Items included: 7 x Acrylic cutouts labeled A-G 1 x Acrylic IO Panel 1 x Acrylic locking plate of PCI cards 2 x Acrylic 5.25 spacers 2 x momentary switches (power/reset) 2 x blue tailed LED w/chrome bezels...
- Page 2 Find the acrylic piece labeled “B”. This is the front of the case. On one side protective film will need to be removed. The other side will already have the film removed and the name “Bob Slay” as well as the Mountain Mods logo etched onto it.
- Page 3 Next take the acrylic panel labeled “C” and remove the film from both sides. Part C is the backside of the case. Looking at the back of the case take a right sided acrylic block and mount to the right side of the case and a left sided acrylic block to the left side of the case.
- Page 4 Now find the panel marked “E”. This is the motherboard tray. Remove the protective film from both sides of the tray. Take the standoffs out of the motherboard hardware bag and mount them into the motherboard tray. Ten holes have been tapped for the standoffs. Some motherboards will not use all standoff points.
- Page 5 Place the case on its side (right side so that you can see the bottom of the case). Now Slide the joined 5.25 devices inside the case from the open side (Do not attempt to slide into the front hole for these devices).
- Page 6 Take the 2 x chrome led bezels with tailed blue LED's and the 2 x nickel plated momentary switches and install them into the front panel. Due to the thickness variation on the acrylic some panels may be too thick to make use of the nut on the chrome bezels. The holes should be tight enough to secure the LED bezel in place.
- Page 7 Now is a good time to install your Motherboard. First take the IO cover panel that comes with your motherboard and insert it into the panel opening. Be very careful. If the panel seems too snug try to take the edges and press them in a bit before forcing into the acrylic panel as this expansion may cause the acrylic IO panel to break.
- Page 8 Remove the protective film from the acrylic locking bar prior to installation. Hold cards into place while screwing down the right side of the locking bar into place. Then put pressure on the left side of the locking bar to align mounting holes and fasten the remaining screw. This should secure your cards and cover plates.
- Page 9 CONGRATULATIONS!!! you should now have something that looks like this. Using the Bob Slay is much easier once it is assembled. To add new cards or manipulate the motherboard portion just remove the top shell. If you need to throw in a cable or replace a drive just remove the left side panel.
Need help?
Do you have a question about the BOB SLAY and is the answer not in the manual?
Questions and answers