Do you have a question about the Eltek Flatpack S 332748 and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for DELTA GROUP Eltek Flatpack S 332748
Page 1
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM Quick Start Guide Document 370012.103, Issue 1.4 Published 23-Mar-16 Flatpack S DC System 1U Configurations Wire Feed DC Distribution SELV Alarming (P/N) Dry Contact Alarming (P/N) 10 GMT Fuses, 2 330180 350196 Rear Feed...
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM IMPORTANT: READ THIS FIRST SAFETY NOTICES – DC Power Systems Read and observe all safety statements and requirements on this sheet before performing any installation or operation work on the power equipment. Failure to comply with the safety statements and requirements contained in this document may result in injury and/or equipment damage, and it may void the user’s authority to operate the equipment.
Page 3
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM Use Underwriters Laboratories (UL)-listed, two-hole lugs for all DC connections to prevent lug rotation and inadvertent contact with other circuits. Terminal strip connections require only single-hole lugs. Wire rated for 90°C is recommended for all DC connections.
Page 4
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM AVERTISSEMENT: DEFAUT D’UTILISER UN DISJONCTEUR CA ET CABLAGE APPROPRIER PEUT RESULTER EN DEFAILLANCE D’ENNUI DE DISJONCTEUR OU FEU. Toujours suivre les codes national et local ainsi que vos pratiques de compagnie pour choisir le câblage CA et les dispositifs de protection.
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM Rectifier Specifications Table 2- Flatpack S Rectifiers NOTE: Ensure that line cords and AC breakers or Flatpack S Rectifiers 48V/1800W HE 48V/1000W HE fuses are properly sized to accommodate the Model (241122.125) (241122.105)
Page 6
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM Removing and Installing Smartpack S Controllers The shelf is shipped with the Smartpack S controller preinstalled. If it is necessary to remove or reinstall the controller, note the following steps. 1.
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM Location of Terminals and Ports – Smartpack S Controller The Smartpack S controller (P/N 242100.410) contains an Ethernet port for a network connection. There are six alarm inputs and six output alarm relays built-in. See the diagram below for a summary of all available terminals and ports.
Page 8
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM Overview: Flatpack S Shelf Specifications Flatpack S 1U shelves are available in a variety of capacities and distribution configurations. The table below summarizes the distinctive features of each shelf. Table 4 –...
Page 9
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM Dimensions (front view) Dimensions (side view) Quick Start Guide Flatpack S DC System ~ Document 370012.103, Issue 1.4, March 2016...
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM Overview: Flatpack S 48V, 3-Rectifier Shelf (332748/320056/350197/350193) 10 GMT Fuses, 2 CBB Circuit Breakers Location of Terminals Make ground wire longer and connect ground first. Spacing is needed between 7A –...
Page 11
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM Overview: Flatpack S 48V, 3-Rectifier Shelf (330180/330179/350196/350204) 10 GMT Fuses, 2 CBB Circuit Breakers Location of Terminals Make ground wire longer and connect ground first. Spacing is needed between 7A–10A loads;...
Page 12
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM Overview: Flatpack S 48V, 3-Rectifier Shelf (350195/350200) 4 CBB Circuit Breakers Make ground wire longer and connect ground first. Quick Start Guide Flatpack S DC System ~ Document 370012.103, Issue 1.4, March 2016...
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM Start Up Before Starting the System 1. Check that all electrical connections are secure. 2. Install rectifiers (if they were not installed already). WARNING: If connecting batteries, note that improper battery connections can cause injury or death and may ignite a fire.
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM COMMISSIONING PROCEDURE System Data Flatpack S System System Order No. Flatpack S Power Supply System, type Article No. Site name Serial No. Software Version No. Rectifiers, type and number of AC Input Voltage, measured Battery Type, if applicable Battery Capacity...
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM MAINTENANCE PROCEDURE System Data Flatpack S PS System Flatpack S Power Supply System, type Article No. Site name Serial No. Software Version No. Rectifiers, type and number of AC Input Voltage, measured Battery Type, if applicable Battery Capacity...
Page 16
ATTACHMENT R & S BID 15-20: 700/800 MHz EDACS and P25 COMMUNICATIONS SYSTEM For assistance with technical questions and solutions, please contact Technical Support by email at tech.support@eltek.com or by phone at 1-800-435-4872. Ordering information: sales.us@eltek.com, (469) 330-9100 Quick Start Guide Flatpack S DC System ~ Document 370012.103, Issue 1.4, March 2016...
Need help?
Do you have a question about the Eltek Flatpack S 332748 and is the answer not in the manual?
Questions and answers