Download Print this page
Magnadyne RVTV-B2 Installation Instructions

Magnadyne RVTV-B2 Installation Instructions

Advertisement

Quick Links

Installation
Step 1: Choosing a Location: Make sure the mounting location has a sufficient
flat area so the antenna's mounting stand can be mounted flat.
Step 2: Drilling Holes: Use the mounting bracket as a template to determine
where to drill the holes.
Step 3: Assembling the Antenna: Rotate the antenna's locking nut all the way down
on the base. Gently pull the antenna's cables thru the mounting stand. Screw
the antenna onto the mounting stand then rotate up the locking nut to lock
the antenna into place.
Step 4: Attaching the Antenna: Feed the cables thru the gasket then thru the hole
in the roof. Put the mounting bolts thru the holes in the mounting stand.
On the interior, place the mounting bracket then use the washers and nuts
to secure the antenna.
Caution: Do not overtighten the mounting bolts, damage to the mounting
stand or roof may occur.
Step 5: Wiring: Connect the cables from the antenna to distribution wall plate and
to the radio. Connect the power cables from the distribution wall plate
according to the diagram below.
Cable Input Plate
(Not Supplied)
TV 1
TV 2
Coaxial Cables
(Purchased
Separately)
Coaxial Cable
(Purchased Separately)
1111 West Victoria Street
Compton, CA 90220
Installation Instructions
Technical Specifications
Frequency range: VHF: 47-230MHz
Receiving range: FM/VHF/UHF
Gain: 30dB
Noise: 3dB
Maximum output level: 110dBµV
Impedance: 75Ω
Power supply: DC 12V
No Connection
(Black)
(for use with
RVTV-B1 or
RVTV-W1 only)
TV 3
(White)
(Black)
Satellite
ON OFF
TV 1
ON = TV
OFF = Cable
(Blue)
Distribution Wall Plate (Supplied Separately)
Models: WS-W (White) or WS-B (Black)
www.magnadyne.com
UHF: 470-862MHz
Satellite Antenna
(Not Supplied )
Red Wire +12V DC
Black Wire Ground
Coaxial Cable
(Purchased Separately)
(Yellow)
Coaxial Cable
(Purchased Separately)
© Copyright 2013 Magnadyne
RVTV-B2 or RVTV-W2 Antenna
Mounting Bracket
Washer
Locking Washer
Nut
For Technical Assistance, please call (800) 638-3600
Models: RVTV-B2 (Black)
RVTV-W2 (White)
Locking Nut
Mounting Stand
Mounting Bolts
Gasket
Vehicle's Roof
AM/FM Receiver (Not Supplied)
Antenna Extension
Cable
(Purchased
Separately)
RVTV-X2-IMUM Rev. A 1-7-13

Advertisement

loading

Summary of Contents for Magnadyne RVTV-B2

  • Page 1 UHF: 470-862MHz where to drill the holes. Receiving range: FM/VHF/UHF RVTV-B2 or RVTV-W2 Antenna Step 3: Assembling the Antenna: Rotate the antenna’s locking nut all the way down Gain: 30dB on the base. Gently pull the antenna’s cables thru the mounting stand. Screw...
  • Page 2 Models: RVTV-B2 (Black) RVTV-W2 (White) Operating Instructions Distribution Wall Plate Features Features: • Compatible with HDTV. 1. Satellite Antenna Output Connector: Use a cable to connect to a TV to receive a satellite signal. • Built-in high gain and low noise amplifier, shielded for minimum Note: A satellite antenna must be connected to the vehicle.

This manual is also suitable for:

Rvtv-w2