Summary of Contents for KM 360-drive
- Page 1 Technical Manual 360-drive Konga Mekaniska Verkstad AB Dång 2 SE 362 93 TINGSRYD Tel: +46 (0) 477 – 549 90 Fax: +49 (0) 477 – 549 99 E- mail: info@kongamek.se Internet: www.kongamek.se...
- Page 2 The machine is delivered by: Konga Mekaniska Verkstad AB Dång 2 SE 362 93 TINGSRYD Tel: +46 (0) 477 – 549 90 Fax: +49 (0) 477 – 549 99 E- mail: info@kongamek.se Internet: www.kongamek.se Technical manual 360-drive page 2 of 26...
-
Page 3: Liability
- If the customer does not meet all its obligations to Konga Mekaniska (financial or otherwise) as satisfied; - For consequential damage caused by faults or defects in the machine (eg damage (processed) products, work interruption, delays, etc.). Technical manual 360-drive page 3 of 26... - Page 4 For goods sold and delivered with factory, importers or wholesalers guarantee applies only by the suppliers guarantee provisions. Regarding warranty on batteries should always charging scheme to be submitted, mentioned in Chap. 7.2. Technical manual 360-drive page 4 of 26...
-
Page 5: Foreword
Konga Mekaniska produces as safe as possible. These machines are designed to the latest standards, according to the CE marking. The user is responsible for the proper use and maintenance of the machine. Technical manual 360-drive page 5 of 26... -
Page 6: Table Of Contents
3.3 GENERAL SAFETY MEASURE ………………………………………………………………….. 4. GENERAL DESCRIPTION OF THE 360-DRIVE ……..……………………………. 4.1 INTENDED USE ……………………………………………………………………………………. 9 4.2 MAIN COMPONENTS OF THE 360-DRIVE ……………………………………………………. 10 4.3 CONTROL ………………………………………………………………………………………….. 5. OPERATING INSTRUCTIONS …………………………………………………. 5.1 INSPECTION BEFORE USING THE 360-DRIVE……………………………………………….. 13 5.2 REVERSE OF THE 360-DRIVE ................... -
Page 7: Markings In Text
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in serious injury or death. DANGER: Indicates a potentially hazardous situation which, if not avoided, will result in serious injury or death. 3.2 Used markings Risk of electric shock Technical manual 360-drive page 7 of 26... -
Page 8: General Safety Measure
- Keep the 360 drive in good working condition by periodic safety inspections. Rectify immediately any unsafe situations, or tag unsafe for use. - The 360-drive may only be used after it has been reviewed and found to be correct with regard to damage, functioning and completeness. -
Page 9: General Description Of The 360-Drive
On the tiller controls are applied, as well as a safety switch. The 360 drive is equipped with batteries that ensure that the 360-drive is independent of continuous 220V AC power. Whenever the 360 drive connected to AC power charges the battery. -
Page 10: Main Components Of The 360-Drive
This brake can be used as a parking brake. Squeeze the handle and move the metal lock on and the brake is permanently pressed. By squeezing the brake further, it will release metal lock and the parking brake is now disengaged. Technical manual 360-drive page 10 of 26... - Page 11 The 360 drive is equipped with a battery condition meter. The capacity of the battery can be read. Caution, do not use it as a guide for loading. The 360-drive should be recharged as many times as possible, preferably after each workday If the BDI ends up in the red field batteries are already damaged.
-
Page 12: Operating Instructions
You may only drive with the 360 drive after you made sure that there are no persons in the danger zones. Allow only qualified, properly trained personnel operate this 360-drive or attempt maintenance on. The 360 drive may only be operated by one person. -
Page 13: Reverse Of The 360-Drive
360 drive. When 360 drive is not in use, remove the key from the ignition switch magnet to exclude unauthorized persons driving the 360-drive. In addition put the 360 drive on the handbrake and disconnect any loads. . -
Page 14: Cleaning Procedure
The 360-drive should be cleaned regularly. Depending on the circumstances, you can use the following tools: - DO NOT CLEAN WITH Hot or cold water high pressure cleaner - Compressed air (specially inside the machine every 3 months) - Suitable scrapers, brushes or abrasive sponges. -
Page 15: Transport
6.2 Storage of the 360-drive When 360-drive is storaged for a long time, take the magnetic key off the tillerhead and disconnect the batteries. If 360 drive is not used for a long period of time due to long transport and / or storage, and the battery is not recharged regularly, it may be that this is over-discharged. -
Page 16: Maintenance Instructions
7. Maintenance instructions During work on the 360-drive the electrical supply should be switched off by means of the magnetic key. In order to avoid unintentional starting, the magnetic key should be taken off from the tillerhead. Furthermore, the poles of the batteries should be disconnected. -
Page 17: Charging The Battery
1. Insert 360-drive near a 230 V outlet. 2. Turn off the 360-drive by taking the magnetic key off the tillerhead. 3. Then insert the plug on/into the 230 volt outlet. Insert the key on the front position (red coloured) of the chassis (Figure 1 page 11) the batteries are being recharged. -
Page 18: Specifications
Width 670 mm Platform Height 130mm Height 160mm low part Height of tiller vertical 1310 mm Speed 6 km / h maximum speed limit Batteries 60 Ah at 24 V Charger 10 A Pulling force 1500 kg on a flat floor. - Page 19 Lighting: Normal ambient lighting. Lighting is not installed on the machine. Altitude: up to 1000 meters above sea level. The machine is not intended for outdoor use. The machine is not suitable for hazardous areas. Technical manual 360-drive page 19 of 26...
-
Page 20: Annex I Ec Declaration Of Conformity
(Safety of industrial trucks - Industrial trucks with capacity up to and including 10000 kg capacity and tractors with a drawbar pull up to and including 20000 N - Part 1: General requirements) Technical manual 360-drive page 20 of 26... - Page 21 (Safety of machinery - Electrical equipment of machines - Part 1: General requirements) NEN 5509 (User manuals - Content, structure, formulation and presentation) Following the provisions of Directives: 98/37/EC (Machinery Directive) 2004/108/EC (EMC Directive) 2006/95/EC (Low Voltage Directive) Technical manual 360-drive page 21 of 26...
- Page 22 Annex II Wiring diagram 360-drive Technical manual 360-drive page 22 of 26...
- Page 23 Technical manual 360-drive page 23 of 26...
- Page 24 Technical manual 360-drive page 24 of 26...
-
Page 25: Annex Iii Technical Drawing
Annex III Technical Drawing Part nr. Part name Qnt. / 360-drive Base frame Cable cover PCB Cover Charging cover Steering bearing Steering bearing mounting ring Cover Steering frame Front wheel Shim front wheel Locking ring front wheel Front wheel cover... - Page 26 Charging connector with cable Fuse holder excl. fuse Fuse 30A Battery indicator cable Control cable Tillerhead Relais set complete Relais Relas cable Controller extension cable Battery cable red Battery cable black Controller cable Technical manual 360-drive page 26 of 26...
Need help?
Do you have a question about the 360-drive and is the answer not in the manual?
Questions and answers