Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Tytan DM-135
- Page 1 DM-135 DRUM MOWER USER’S MANUAL...
-
Page 2: Chapter 1 Safe Operation
DM135 DRUM MOWER INSTRUCTIONS CHAPTER 1 SAFE OPERATION Do not attempt to operate the mower until you have read the operator’s manual and all the safety signs on the mower. NOTE: The words Danger, Warning or Caution on the safety signs indicate a hazard or unsafe practice, which could result in injury or death if proper precautions are not taken. -
Page 3: Safety Instructions
CAREFULLY READ OPERATORS MANUAL BEFORE HANDLING MOWER A． Keep a sufficient protection distance from the drum knife when the engine is in operation. B． Do not touch any moving part. Wait until all parts of the mower are at rest when you want to check and maintenance the mower. -
Page 4: During Transport
before working on or near mower for any reason including cleaning, inspecting or servicing machine. 2. The tractor Power take-off must be equipped with an over-riding clutch or one must be added to the mower PTO shaft. 3. Keep hands and feet away from rotating blades and other moving parts. 4. -
Page 5: Chapter 2 Specifications
Replacement decals can be purchased from your dealer CHAPTER 2 SPECIFICATIONS TRACTOR SPECIFICATIONS CAUTION: Do not operate mower with a tractor that does not comply with the following requirements: Ⅰ .Horsepower-27(minimum) Ⅱ .Counter balance weight :It may be necessary to add weight to the front end and/or left rear wheel of your tractor to maintain adequate tractor stability and weight of your tractor and the conditions in which you are operating your tractor. -
Page 6: Safety Breakaway
not be disturbed when the mower is operating. Imbalance may cause excessive vibration, which in turn may cause damage to the machine. If you notice abnormal vibration in the machine or a change in the noise that the machine produces, stop immediately and inspect the machine. CAUTION: Disengage PTO, stop tractor engine, set park brake and wait for blade rotation to stop before working on blades, drums or saucers. - Page 7 removing the saucers and the blade holder. Figure B (40 degrees). Figure B 8. Tighten Allen screws of saucers securely and recheck after a few working hours. 9. The PTO drive shaft may have to be shortened to fit your particular tractor. The shaft should be shortened a minimum amount only.
-
Page 8: Cutting Height Adjustment
10. Be sure protective curtains and shields are in place and in good condition. Adjust the lower arms of the tractor 3-point in such a way that the mower will be raised horizontally in mowing position. CUTTING HEIGHT ADJUSTMENT The cutting height may be adjusted slightly be means of the top link. -
Page 9: Maintenance And Lubrication Instructions
touches the stop #4. 3． Relock the nut #1. Tensioning of the V belts is only necessary if belts are slipping. Maximum tension in when the indicator is about 1/8” clearance from the bottom. If a V belt breaks or comes off, the whole set of belts should be replaced. NOTE: If the V belts are over tensioned, damage will occur to the gearbox input shaft bearings and main drive shaft bearings. -
Page 10: Chapter5 Parts List
CHAPTER5 PARTS LIST The DM135 mower is a two—drum mower. Each drum has three knives, which can be changed quickly with a simple tool. The hay cut by the knives is carried between the drums and put in a loosely laid swath. Three V—belts transmit power to the input gear shaft, then to the main drive shaft, which in turn drives the drums through the bevel gears. - Page 11 ITEM NO. DESCRIPTIONS REMARK Part NO。 零 件 名 称 DM135.10.001 MOWERING 割 草 机 割 草 器 ASSEMBLY DM135.20.001 TRANSMISSION 皮 带 传 动 部 分 ASSEMBLY DM135.30.001 COVER 割 草 机 罩 壳 DM135.40.001 HANDLE, BLADE 割 草 机 卸 刀 架 REPLACEMENT DM135.50.001 PTO SHAFT...
- Page 12 ITEM NO. Part NO。 DESCRIPTIONS REMARK 零 件 名 称 DM135.10.010 Saucer 滑 板 焊 合 件 DM135.10.101 Saucer holder 滑 板 连 接 座 GB/T276-1994 Bearing 6210 轴 承 6210 GB/T301-1995 Bearing 51109 轴 承 51109 GB/T276-1994 Bearing 6207 轴...
- Page 13 GB/T889.2-2000 Lock Nut M16x1.5 防 松 螺 母 M16X1.5 DM135.10.104 Hub, driving 驱 动 盘 驱 动 盘 防 松 螺 栓 DM135.10.105 Bolt M16X1.5 M16X1.5 GB1096-2003 Key 8X7X55 平 键 8X7X55 DM135.10.106 Gasket 调 整 垫 圈 1 DM135.10.013 Main frame 箱...
- Page 14 DM135.10.123 Spacer 小 带 轮 轴 定 位 隔 套 GB5782-2000 Bolt M10X60 螺 栓 M10X60 GB/T889.1-2000 防 松 螺 母 M10 JB/ZQ4450-1986 Plug M20X1.5 外 六 角 螺 塞 M20X1.5 GB6173-2000 M20X1.5 六 角 薄 螺 母 M20X1.5 JB/ZQ4454-1986 铜...
- Page 15 GB/T6170-2000 螺 母 M10 DM135.20.104 Spacer 长 套 管 GB5782-2000 Bolt M10X100 螺 栓 M10X100 DM135.20.105 Extension spring 热 卷 拉 伸 弹 簧 DM135.20.013 Linkage 联 板 焊 合 件 DM135.20.106 16X112 销 轴 16X112 DM135.20.014 连 接 套 焊 接 件 DM135.20.015 Hitch frame 悬...
- Page 16 GB/T276-93 Bearing 6207 轴 承 6207 DM135.20.127 Spline shaft 花 键 轴 DM135.20.018 Transport bar 固 定 杆 焊 合 件 DM135.20.129 长 销 子 15.8 DM135.20.128 快 速 挡 销 1 DM135.20.019 Pivot 连 接 轴 焊 合 件 DM135.20.121 Adjustment washer...
- Page 17 ITEM NO. Part NO。 DESCRIPTIONS REMARK 零 件 名 称 GB5783-2000 Bolt M6X16 螺 栓 M6X16 GB/T97.1-2002 平 垫 6 Plain washer GB/T93-2000 Lock washer 弹 垫 6 GB/T6170-2000 螺 母 M6 DM135.30.101 Tarpaulin 篷 布 DM135.30.010 Frame, weldment 罩 壳 焊 合 件...
Need help?
Do you have a question about the DM-135 and is the answer not in the manual?
Questions and answers