Nortek Security & Control GoControl GD00BLE-1 Installation Instructions

GD00BLE-1
EXCLUSIVELY
©
FOR WALMART
GARAGE DOOR
OPENER
REMOTE COMMAND
TRANSCEIVER
with TILT SENSOR
Available if needed
Installation Instructions
3
PRODUCT COMPONENTS
GD00BLE-1
STATUS
POWER
INDICATOR
INPUT
JACK
CONNECTION
WIRES
OPTIONAL
ADJUSTABLE
GD00BLE-1 MOUNTING
BRACKET
SCREW AND
MOUNTING HARDWARE
FOR ADJUSTABLE
TILT
BRACKET
SENSOR
SCREWS AND
MOUNTING TAPE
FOR TILT SENSOR
INSTR,INSTL,GD00BLE-1 - P/N: 10026532 X8 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000" X 8.500" - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
1
PRODUCT DESCRIPTION
GD00BLE-1 Summary of Operation
• GD00BLE-1 connects to the garage
door opener's pushbutton wall console
terminals.
• A wireless tilt sensor mounts on garage
door and reports door's position to
GD00BLE-1.
• GD00BLE-1 uses BLE for communication
to open or close the garage.
• A warning indicator light flashes and a
beeper sounds for 5 seconds before the
door begins to move.
• If the door does not completely open or
close, a second open or close command
can be sent after 30 seconds.
• If the door does not completely open
or close after the second attempt, the
GD00BLE-1 operation is suspended until a
local garage door pushbutton is activated.
Reserved for HomeKit QR Code and label
4
TILT SENSOR INSTALLATION AND BATTERY
WARNING
LIGHT 1
LINK
BUTTON
MOUNTING SCREWS
AND ANCHORS
FOR GD00BLE-1
WIRE
TIES
The system will notify you
when the battery is low,
replace the battery with
a type CR2032 coin cell
POWER
SUPPLY
1
To open the case, twist
a small screwdriver
in case slot
PRINTER'S INSTRUCTIONS:
©
Please download the Walmart InHome
app from the Apple or Android PlayStore.
Reserved for
Walmart URL pointer
on-boarding text and
QR Code
To activate the tilt sensor,
remove the battery protection pull strip
2 3
Attach the mounting plate Snap the sensor onto
to the top panel of the door the mounting plate
ARROWS ON PLATE
& SENSOR POINT UP
"UP"
ARROWS
POST ON
BOTTOM
Use double sided tape or
the two mounting screws supplied
(drill 1/16" pilot holes if required)
LOW BATTERY REPLACEMENT
PLUS SIDE UP !!!
2
Insert the CR2032
battery
into the
transmitter
SLOT
2
SAFETY NOTES
WARNING
This operator system is equipped with an unattended
operation feature. This door could move unexpectedly. NO
ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type doors only per
(UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
The Remote Command Transceiver must be mounted in the
garage, in sight of the garage door, where the visual and audible
movement warning indicators can be clearly seen and heard.
WARNING
Do not install the Remote Command Transceiver on garage
door operators manufactured prior to 1993 (models without
an operational safety beam entrapment detection system).
5
PAIRING TILT SENSOR & RESETTING TO FACTORY DEFAULTS
WALL
OUTLET
GD00BLE-1
POWER
POWER
SUPPLY
INPUT
JACK
The GD00BLE has already been set to factory defaults and pre-paired with the
tilt sensor. NO RESET OR PAIRING IS REQUIRED. The following instructions are
provided for reference only
• Quickly pressing the LINK button 5 times will reset the GD00BLE to the factory
defaults (Tilt pairing will be preserved).
• Long pressing with LINK button (3-5 seconds) until an audible beep is heard will
re-pair/learn the Tilt Sensor.
Reserved for Bluetooth QR Code
LINK
BUTTON