Advertisement
Quick Links
Advertisement
Related Manuals for Schulz Speyer Concertina
Summary of Contents for Schulz Speyer Concertina
- Page 1 Assembly Guide Concertina...
- Page 2 Assembly guide Assembly guide for Concertina Pos. Specifications Tape (Scotch Bronel), length 35 cm Bosscod 4 mm BN 717 Sheet metal screw 4,8X13 mm Cylinder nut M6X13 mm JS no. 4081 961013 6X45 mm HFC 683 4X20 mm HFC 681...
- Page 3 Assembly guide Assembly guide for Concertina...
- Page 4 Assembly guide Assembly guide for Concertina...
- Page 5 Assembly guide Assembly guide for Concertina...
- Page 6 Assembly guide Assembly guide for Concertina Straight Curved...
- Page 7 Assembly guide Assembly guide for Concertina...
- Page 8 Assembly guide Assembly guide for Concertina...
- Page 9 Assembly guide Assembly guide for Concertina...
- Page 10 Assembly guide Assembly guide for Concertina...
- Page 11 Assembly guide Assembly guide for Concertina Manual adjustable...
- Page 12 Assembly guide Assembly guide for Concertina Electrical adjustable...
- Page 13 Assembly guide Assembly guide for Concertina...
- Page 14 Assembly guide Assembly guide for Concertina...
- Page 15 Assembly guide Assembly guide for Concertina...
- Page 16 Assembly guide Assembly guide for Concertina...
- Page 17 Assembly guide Assembly guide for Concertina...
- Page 18 Assembly guide for Concertina Electrically adjustable module: Adjustment instructions If electrically adjustable Concertina desk surfaces have an uneven weight load or intensive use condition, the motor will on occasion require calibration. The facility staff can easily accomplish this by lowering the unit(s) to what is termed a zero position or the lowest possible point of adjustment and press the button for a minimum of 5 sec.
- Page 19 Assembly guide Assembly guide for Concertina Safety instructions for the Desk Power System Safe use of the system is possible only when the operating instruction are read completely, and the instructions contained are strictly observed. Failure to comply with instructions marked with “NOTE” may result in serious damage to the system or one of its components.
- Page 20 Assembly guide Assembly guide for Concertina Control for adjusting the table height...
- Page 21 Assembly guide Assembly guide for Concertina Initialisation of the parallel system: The Desk Power System is initialized by pressing the down key once or twice and holing it down until the actuator runs into end stop. It will then automatically run approx. 5 mm out again hereafter slowly running in again. Only release the down key when the movement has completely stopped.
- Page 22 Assembly guide Assembly guide for Concertina Upper front panel Front fitting Lower front panel Upper front panel Tape Internal lower panel Screw...
- Page 23 Assembly guide Assembly guide for Concertina 660 mm Upper front panel 780 mm projection towards client Upper front panel 780 mm projection towards client Upper front panel 900 mm Upper front panel Always align the upper front to the inside of the front ledge...
- Page 24 GERMANY DENMARK BELGIUM/HOLLAND Schulz Speyer Bibliothekstechnik AG Lammhults Biblioteksdesign A/S SBNL – Schulz Benelux BVBA Friedrich-Ebert-Straβe 2a Dalbækvej 1 Appelweg 94 C 67346 Speyer 6670 Holsted 3221 Holsbeek sales@schulzspeyer.de bci@bci.dk info@sbnl.be www.schulzspeyer.de www.lammhultsbiblioteksdesign.dk www.sbnl.be FRANCE SWEDEN BC Interieur S.A.R.I. Lammhults Biblioteksdesign AB 8, Allée Lorentz...
Need help?
Do you have a question about the Concertina and is the answer not in the manual?
Questions and answers