Advertisement
5.7.
To drain the oil, remove the filler plug and raise front of jack. Make sure that no dirt is allowed to enter the hydraulic system.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THIS PRODUCT.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN JACKS TO US. Please telephone us on 01284 757500 to obtain the address and 'phone number of your local agent.
If jack is under guarantee contact your local Sealey dealer.
De-commissioning the Jack - Should the jack become completely unserviceable and require disposal, draw off the oil into an approved
container and dispose of the jack and the oil according to local regulations.
AXLE STANDS
5.8.
Before each use check to ensure stands and stand welds are not cracked, and that there are no missing and/or damaged parts.
WARNING! Any stand that appears to be damaged in any way must be removed from service immediately.
#
5.9.
Ensure the locking pin, folding arms and mechanism are in good order and condition.
5.10. Due to the potential hazards associated with these stands, do not misuse, or make any modification to the stands or components.
6.
TROUBLESHOOTING
IMPORTANT: MAINTENANCE OR REPAIR OF HYDRAULIC SYSTEM MUST ONLY BE PERFORMED BY A QUALIFIED PERSON.
PROBLEM
POSSIBLE CAUSE
1) Overloaded
Jack will not lift
2) Oil level low
the load
3) Release valve not correctly closed
4) Air in system
5) Piston rod not functioning
6) Packing worn or defective
1) Oil level too high or too low
Jack does not lift
2) Worn seals
high enough or
3) Air in system
feels "spongy"
4) Release valve not closed
1) Pump packing or valves malfunctioning
Jack lifts poorly
2) Oil is dirty
3) Air in the system
1) Release valve partially open
Jack lifts but will
2) Dirt on valve seats
not hold load
3) Air in system
4) Faulty seals
5) Packing worn or defective
1) Unit requires lubrication
Jack will not lower
2) Piston rod bent or damaged
completely
3) Jack frame/link system distorted due
to overloading/poor positioning
4) Air in system
5) Release valve partially closed
6) Jack spring damaged or unhooked.
1) Release valve closed
Jack does not
lower at all
Declaration of Conformity
TROLLEY JACK
Model: 1030CXDK
93/68/EEC CE Marking Directive
2006/42/EC Machinery Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: Call 01284 757525 for our catalogue & promotions. Leave your full name, address & postcode.
REMEDY
1) Be sure to use jack with adequate capacity
2) Top up oil level
3) Check and close release valve
4) Open release valve and pump the handle a few times. Close valve and re-try
5) Clean and replace oil
6) Replace packing
1) Fill or remove excess oil
2) Return jack to local service agent
3) Open release valve and pump the handle a few times. Close valve and re-try
4) Check and close release valve
1) Replace packing and/or clean valves
2) Replace oil
3) Open release valve and pump the handle a few times. Close valve and re-try
1) Check and close release valve
2) Lower jack, close release valve. Place foot on front wheel and pull up lifting arm to it's full height by hand.
Open the release valve to lower arm
3) Open release valve and pump the handle a few times. Close valve and re-try
4) Replace packing or contact local service agent
5) Replace packing
1) Oil all external moving parts
2) Replace rod or contact local service agent
3) Replace damaged parts or contact local service agent
4) Open release valve and pump the handle a few times. Close valve and re-try
5) Check and fully open release valve
6) Replace spring or contact local service agent
1) Check and fully open release valve
We, the sole importer into the UK, declare that the product listed below is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a national
authority, upon contact Jack Sealey Ltd.
Signed by Mark Sweetman
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
01284 757500
01284 703534
25th October 2007
www.sealey.co.uk
Web
sales@sealey.co.uk
email
1030CXDK - 1 - 251007
Advertisement
