Summary of Contents for ECI MOVFR
- Page 1 MOVFR – LCD Door Board Installation Manual REV: 2.2 DATE: 5/14/2018 MANUAL NUMBER: 37 Electronic Controls Inc 7073 North Atlantic Ave Cape Canaveral, FL 32920 WWW.ECIAMERICA.COM 800-633-9788...
- Page 2 ECI MOVFR-LCD Installation Manual DATE DESCRIPTION 10/25/2017 INITIAL RELEASE 11/2/2017 Added installation Kits, AUTO Operation 4/13/2017 Added new logo 5/4/2018 Removed CL/HCL Max Speed , Added Light curtain parameter 5/14/2018 Added drill template directions Electronic Controls, Inc. 7073 North Atlantic Ave. Cape Canaveral, FL 32920 800-633-9788 www.eciamerica.com...
-
Page 3: Table Of Contents
ECI MOVFR-LCD Installation Manual Table of Contents Warning and Disclaimer ........................5 Introduction ............................6 Conventions Used ..........................6 Safety Information ..........................7 System Overview ..........................8 Control Board ..........................8 5.1.1 Electrical ..........................8 5.1.2 Connections ........................... 8 5.1.2.1 Input Signals ........................ - Page 4 8.2.1 Right Hand CAMs ......................25 8.2.2 Left Hand CAMs ......................... 26 AUTO Operation ..........................26 Drill template for MOVFR-0001N replacement ................27 Electronic Controls, Inc. 7073 North Atlantic Ave. Cape Canaveral, FL 32920 800-633-9788 www.eciamerica.com P a g e...
-
Page 5: Warning And Disclaimer
ECI MOVFR-LCD Installation Manual 1 Warning and Disclaimer Thank you for purchasing equipment from ECI America, INC. We want your new equipment to operate safely. Anyone who installs or uses this equipment should read this publication (and any other relevant publications) before installing or operating the equipment. -
Page 6: Introduction
The ECI MOVFR (Variable Frequency Drive) LCD Door Operating system is a 2 board combination designed to be a drop in replacement for the GAL MOVFR door operator. The ECI VFD LCD door operator includes a 230VAC input Variable Frequency Drive (VFD) board and a control board with key pad and LCD screen. -
Page 7: Safety Information
ECI MOVFR-LCD Installation Manual 4 Safety Information Know the safety hazards related to any procedure you are about to perform. Know what equipment has been specified for each specific contact and know what tools and materials you should plan to have available. Before connecting electrical wiring, take precautions to prevent accidents from happening to yourself and others around you. -
Page 8: System Overview
ECI MOVFR-LCD Installation Manual 5 System Overview 5.1 Control Board Figure 1 - Control Board 5.1.1 Electrical 5.1.2 Connections 5.1.2.1 Input Signals • CLOSE – Any 24 to 240 VAC/VDC input between CLOSE and COM will produce a CLOSE operation. -
Page 9: Interfacing With Light Curtain
ECI MOVFR-LCD Installation Manual • REOPEN NO • REOPEN COM REOPEN Relay contacts rated at 230V 10A. Energized • REOPEN NC when torque limit exceeded, obstruction of light curtain. • DCL NO • DCL COM DCL Relay. Door Close Limit contacts rated at 230V 10A. Energized when •... -
Page 10: User Interface
ECI MOVFR-LCD Installation Manual Figure 4- Tri-Tronics® wiring 5.1.3 User Interface 5.1.3.1 LCD Screen Main Menu ECI MOVFR (C) 2018 ECI Inc. Edit parameters Load defaults Diagnostics 1 Diagnostics 2 Figure 5 - LCD Screen Main Menu Figure 5 - LCD Screen shows the main menu. Pressing the “-“ button moves the curser down to the next selection. -
Page 11: Keypad
ECI MOVFR-LCD Installation Manual • SSO – Slow Start Open. Speed setting is OP slow start. When illuminated indicates the start of the open cycle when the interlock rollers unlock hoistway door. SSO/FSO sensor blocked and MSO sensor open during an OPEN cycle. -
Page 12: Cam Optical Sensors
ECI MOVFR-LCD Installation Manual • AUTO / MAN – 2 position switch. AUTO position is for normal operation. MAN position is for controlling the doors using OPEN, CLOSE, HEAVY and NUDGE switches. • CLOSE / OPEN – 3 position switch. Center position no function. With AUTO/MAN switch in manual position this controls opening and closing the doors. - Page 13 ECI MOVFR-LCD Installation Manual CAUTION: Holding power should be set less than 15W to prevent motor heating which will reduce motor life. • CL hold sp. – Enabled when the door reaches DCL and the parameter is greater than 0.
-
Page 14: Heavy Door Parameter Settings With Defaults
ECI MOVFR-LCD Installation Manual • OP decel – A lower value produces a quicker deceleration. This should be set so the OP Final Speed FSO is reached before the DOL and OPEN stop roller to prevent slamming and bouncing. The default setting is 50. Min is 1 and max is 100. -
Page 15: Input Voltage Setting Parameter
ECI MOVFR-LCD Installation Manual 5.1.5.1.3 Input Voltage setting Parameter • Input voltage – Parameter for setting valid AC/DC voltage for CLOSE, OPEN, NUDGE and HEAVY inputs. Default setting is 24. Minimum is 12 and max is 240. Voltages below these settings will not be detected by the control board. -
Page 16: Variable Frequency Drive Board (Vfd Board)
ECI MOVFR-LCD Installation Manual 5.2 Variable Frequency Drive Board (VFD Board) Figure 8 - Variable Frequency Drive Board 5.2.1 Frequency Board Electrical • 220VAC • 5A 250V fuse 5.2.2 Frequency Board Connections • L1 and L2 – 240 VAC input power •... -
Page 17: Installation
• Disconnect power from drive. • Remove Control board and Drive shown in Figure 10 - MOVFR-0001N (shown without CAMs) Figure 10 - MOVFR-0001N • Remove the standoffs indicated in Figure 11 - Standoff Removal leaving the 2 standoffs on the far right and the 2 nylon standoffs in the center. - Page 18 ECI MOVFR-LCD Installation Manual Remove Keep Figure 11 - Standoff Removal Figure 12 - Snapping Off Standoff • Remove drill template from manual (last page of manual). Fold or cut page of drill template along dotted lines and place in top left corner of operator as shown in Figure 13 - Drill Pattern placement Electronic Controls, Inc.
- Page 19 Figure 14 - Standoff Placement • Using hardware supplied with the board, mount the Control and Drive boards as shown in Figure 15 -ECI MOVFR LCD Installed. Connect communication cable (supplied with boards) between Control and Drive boards. Electronic Controls, Inc.
-
Page 20: Replacing Movfr-0069N
• Remove the Control Board and Drive shown in Figure 17 - MOVFR-0069N • Mount and secure the ECI MOVFR-LCD Control board and Drive board as shown in Figure 18 - ECI MOVFR-LCD Installed. • Connect communication cable (CAT5) between Control and Drive Boards. - Page 21 ECI MOVFR-LCD Installation Manual Figure 17 - MOVFR-0069N Figure 18 - ECI MOVFR-LCD Installed Electronic Controls, Inc. 7073 North Atlantic Ave. Cape Canaveral, FL 32920 800-633-9788 www.eciamerica.com P a g e | 21...
-
Page 22: Initial Power Up And Test
ECI MOVFR-LCD Installation Manual 7 Initial Power Up and Test 7.1 Manual Operation • With the doors in the fully closed position and the AUTO/MAN switch in the MAN position, apply power to door operator o LCD Display should show... -
Page 23: Adjustments
ECI MOVFR-LCD Installation Manual ▪ When fully OPEN the SPEED and MOTOR reading should go to 0 even with the switch in OPEN position. o NOTE that the HOLDING LED will not light as the OP HOLD SP and TORQ settings are at default 0 settings. -
Page 24: Speed Profiles
ECI MOVFR-LCD Installation Manual 8.1 Speed Profiles 8.1.1 Closing Speed Profile Figure 19- Close Speed Profile 8.1.2 Closing CAM/Sensor Sequence Figure 20 - Close CAM/Sensor Sequence 8.1.3 Open Speed Profile Figure 21 - Open Speed Profile Electronic Controls, Inc. 7073 North Atlantic Ave. Cape Canaveral, FL 32920 800-633-9788 www.eciamerica.com... -
Page 25: Open Cam/Sensor Sequence
ECI MOVFR-LCD Installation Manual 8.1.4 Open CAM/Sensor Sequence Figure 22 - OPEN CAM/SENSOR Sequence 8.2 CAM Settings 8.2.1 Right Hand CAMs Figure 23- Right Hand CAM Settings Electronic Controls, Inc. 7073 North Atlantic Ave. Cape Canaveral, FL 32920 800-633-9788 www.eciamerica.com... -
Page 26: Left Hand Cams
ECI MOVFR-LCD Installation Manual 8.2.2 Left Hand CAMs Figure 24 - Left Hand CAM Settings 9 AUTO Operation • Go to EDIT PARAMETERS and change the INPUT VOLTAGE parameter to the proper voltage for your system. • Switch the AUTO/MAN switch to AUTO position. -
Page 27: Drill Template For Movfr-0001N Replacement
ECI MOVFR-LCD Installation Manual 10 Drill template for MOVFR-0001N replacement FOLD OR CUT PAGE ALONG DOTTED LINES Electronic Controls, Inc. 7073 North Atlantic Ave. Cape Canaveral, FL 32920 800-633-9788 www.eciamerica.com P a g e | 27...