Related Manuals for schweisskraft VarioProtect 3XL-W Digital TC
Summary of Contents for schweisskraft VarioProtect 3XL-W Digital TC
- Page 1 Operating Instructions Automatic Welding Helmet VarioProtect 3XL-W Digital TC VarioProtect 3XL-W Digital TC...
-
Page 2: Table Of Contents
Passing on as well as copying of this document, the use and distribution of its content are prohibited if not explicitly permitted. Contraventions are liable to compensation. Subject to technical modifications and error. VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 3: Introduction
VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 4: Safety Regulations
- Check the welding helmet for visible damage and defects before use. Repair defects and damage im- mediately. - Do not use the welding helmet in wet environments, rain, etc. VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 5: Intended Use
Cassette width [mm] manufacturer for resulting damages to persons or objects and cause an expiration of the warranty claim! Cassette height [mm] Sensitivity 0 -7, automatic Lens thickness [mm] VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 6: Description Of The Helmet
D Auto darkening filter E Inner pane F Nut Fig. 1: Description of the helmet VarioProtect 3XL-W Digital TC The button 11 can be used to switch between the grin- ding mode (GRIND) and the welding mode (WELD) without taking off the welding helmet. - Page 7 10 lux. The conditions for sleep mode and wake-up mode are shown in the table below. VarioProtect 3XL-W Digital TC | Version 1.02 | EN...
-
Page 8: Wearing Parts
The solar cells of the filter should be stored in the dark or not exposed to light. The solar cells of the filter should be stored in the dark and not exposed to light. VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 9: Product Characteristics / Adjustment Options
"AUTO" is displayed in the SENS area. The sensitivity levels increase from 0 to 7 and stop at the level number that is automatically set. Then the system quits the automatic sensitivity setting mode. VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 10: Setting The Operating Mode
Level 0 to 9 of the delay time equals 0.06 s to 1.2 s. Fig. 4: Control panel Level 0 is suitable for TAC welding. Various sensitivities and delays can be set in the Welding and Cutting mode. VarioProtect 3XL-W Digital TC | Version 1.02 | EN... - Page 11 Releasing the key and pressing it again in- creases the tinting level again. 2. Long keystroke: Press for more than 1.5 s to quickly in- crease the tint level. VarioProtect 3XL-W Digital TC | Version 1.02 | EN...
-
Page 12: Protection Level Setting
6d. After the adjustment mechanisms have been carried out, the helmet should feel more comfortable for the welder to wear than before. Work can be performed with high pre- cision throughout. VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 13: Notes Before Commissioning
- Make sure that optical radiation from the arcs of other welders in the immediate vicinity does not VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 14: Operation
Verzögerung zu hoch eingestellt. Set delay. pleting the welding process Umgebungslicht ist zu hell. Reduce the light level. Welding splashes damage the filter Fehlende, beschädigte, gebrochene, Replace the front cover shield. verzerrte Frontabdeckung. VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 15: Color Table
The user must immediately remove the welding hel- met if the above problems cannot be solved. Contact your dealer. 11 Color Table Recommended shade guide according to EN 169. Fig. 7: Color table VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 16: Meaning Of The Marking
Do not use strong detergents or solvents: clean the inside and outside of the helmet with a neutral disin- fectant. VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 17: Replace Front Pane And Filter
5. Use the tool ( at the back of the battery compartment cover) to remove the batteries (G). Insert new batte- ries and close the battery compartment cover again. Fig. 10: Replacing filter and front pane VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 18: Change Welding Filter
- Do not allow the filter to come into contact with li- quid or dirt. - Do not open the filter container. Do not use tools or other sharp objects to remove parts of the filter or helmet. VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 19: Spare Parts
You will find information regarding the device type, item No. and year of manufacture on the type plate fixed to the welding helmet. VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 20: Spare Parts Drawing
The following drawing should help you to identify necessary spare parts in case of service. If necessary, send a copy of the parts drawing with the marked components to your dealer. Fig. 14: Spare parts drawing VarioProtect 3XL-W Digital TC VarioProtect 3XL-W Digital TC | Version 1.02 | EN... - Page 21 Left Adjustable Washer Linke Begrenzungsscheibe Left Limitation Washer Helmschale Helmet shell Äußere Vorsatzscheibe Front protection plate Pressrahmen Press frame Automatikabdunkellungsfilter Auto darkening Filter Innere Vorsatzscheibe Rear protection plate Mutter Peripherie-Wahrnehmungsfilter Peripheral awareness filter VarioProtect 3XL-W Digital TC | Version 1.02 | EN...
-
Page 22: Eu - Declaration Of Conformity
DIN EN 379: 2003 + A1:2009 Personal eye protection - Automatic welding protection filters Responsible for documentation: Kilian Stürmer, Stürmer Maschinen GmbH, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 20.04.2020 ______________________ Kilian Stürmer Managing Director VarioProtect 3XL-W Digital TC | Version 1.02 | EN... -
Page 23: Notes
Notes 17 Notes VarioProtect 3XL-W Digital TC | Version 1.02 | EN... - Page 24 www.schweißkraft.de...
Need help?
Do you have a question about the VarioProtect 3XL-W Digital TC and is the answer not in the manual?
Questions and answers