Related Manuals for Monacor AXOC-2812BV
Summary of Contents for Monacor AXOC-2812BV
- Page 1 Full HD 1080P AHD Bullet Camera AXOC-2812BV Thanks for purchasing our product. Before operating the unit, please read the instructions carefully and keep this manual for future reference.
- Page 2 Safety Warning 1. Read this manual carefully before installing the unit Please read this manual first for correct installation and operation. 2. Never install the camera on a ceiling that cannot hold its weight The product may fall down and cause damages. 3.
- Page 3 10. Cleaning Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 11. Never disassemble the camera nor put impurities in it Disassembly or impurities may result in trouble or fire. 12.
-
Page 4: Table Of Contents
Table of Contents 1. CAMERA ...................... 1 ....................1 EATURE ................... 1 IST OF ONTENTS ..................... 1 IMENSIONS ..................2 PECIFICATION & C ........3 AMERA ARTS ONNECTION TO OWER 2. CAMERA OSD ..................... 4 2.1 M ......................6 2.2 LENS ......................7 2.3 E .................... -
Page 5: Camera
1. CAMERA Feature Full HD 1920x1080P@25/30fps (AHD) 1/3” Sony 2.4M Exmor CMOS Sensor Color: 0.1 Lux, B/W: 0.06 Lux, IR On: 0 Lux @F1.6 Video Output: AHD / Composite BNC OSD Control / CoC (Disabled in PoC models) ... -
Page 6: Specification
Specification Image Sensor 1/3” Sony 2.4M Exmor CMOS Sensor Video Frame Rate 1920x1080p@25/30fps, 1280x720p@30fps Minimum Illumination Color: 0.1 Lux, B/W: 0.06 Lux, IR On: 0 Lux @F1.6 Wide Dynamic Range 90dB Video Output BNC connector (AHD) & Composite Simultaneous (Option) ; Composite is disabled when WDR ON Mechanical IR Cut Filter (ICR) IR LED ;... -
Page 7: Camera Parts & Connection To Power Unit
Camera Parts & Connection to Power Unit ① OSD Control Buttons (depends on model) ENTER button UP & DOWN buttons LEFT & RIGHT buttons ② AHD Cable For AHD signal output, it supports Power over Coaxial cable (Option) technology. ③ Video Out (BNC Connector) For analog composite video TV signal output. -
Page 8: Camera Osd
2. Camera OSD To operate the camera OSD setting, use the control key pad to control it. For some models, you might need to open the control panel case to access the control key panel. Press the Enter button which in the center of the control panel to bring up the "MENU" on the TV/Monitor screen as below. Please check the OSD content tables to find out the function you need. - Page 9 GAMMA MIRROR FLIP BLACK LEVEL RETURN <┘ ■ Effect EFFECT Default Value MOTION PRIVACY D-ZOOM 1.0X DEFOG RETURN <┘ ■ System SYSTEM Default Value DIGITAL OUT 1080P FRAME RATE 30 FPS ANALOG OUT NTSC <┘ CABLE LENGTH 0-200M COLORBAR LANGUAGE ENGLISH FW 4.0 AH120 160907107NBXJC04...
-
Page 10: Menu
Menu In the "MENU" of camera OSD, there are several sub-menus and items can be selected to modify the settings. ■ LENS: To select the lens is on AUTO IRIS or on MANUAL. Models with Motorized lens have IR Calibration function enabled. ■... -
Page 11: Lens
LENS In the "LENS" of camera OSD, there are some items can be selected to modify the settings. Users can switch lens mode between AUTO IRIS and MANUAL and adjust the optical settings accordingly. For non-motorized lens models For motorized lens models ■... -
Page 12: Exposure
Exposure In the "EXPOSURE" of camera OSD, there are some items can be selected to modify the settings. The main function of this page is about the optical settings. AUTO IRIS LENS MANUAL LENS ■ MODE: INDOOR is recommended for BOX type models. OUTDOOR is recommended for other models with either AUTO IRIS or AUTO IRIS plus IR function. - Page 13 AUTO SHUTTER (INDOOR) AUTO SHUTTER (OUTDOOR) MANUAL SHUTTER ■ SHUTTER: (MANUAL LENS) AUTO, MANUAL, 2 options available. The value of SHUTTER MIN/MAX speed for AUTO and MANUAL modes can be further adjusted as shown in the screenshots below. The defaults of SHTTER MIN/MAX are 1/30 and 1/30000 for AUTO SHUTTER; while the default MANUAL SHUTTER SPEED has no change (1/30).
-
Page 14: Wdr/Blc
WDR/BLC In the "WDR/BLC" of camera OSD, total 4 options are available and 3 of which have advanced settings menu for adjustment. Please see details below. ■ D-WDR: LEVEL can be adjusted, but it’s disabled under Factory Default (Restore setting). ■... -
Page 15: White Bal
WHITE BAL In the "WHITE BAL" of camera OSD, total 4 options are available and 2 of which have advanced settings menu for adjustment. Please see details below. ■ MANUAL: KELVIN: To adjust the KELVIN (Color temperature) value among LOW/MIDDLE/HIGH. R-GAIN: To adjust the R-GAIN (RED GAIN) value from 0 to 20. -
Page 16: Dnr
In the "DNR" of camera OSD, there are some items can be selected to modify the settings. The main function of this page is to adjust the digital noise reduction. ■ SMART DNR: To enable or disable SMART DNR mode. Default setting is ON as of recommended use. ■... -
Page 17: Day/Night
DAY/NIGHT In the "DAY/NIGHT" of camera OSD, AUTO, IR SYNC, and B/W, can be selected to modify the settings. Selecting COLOR will keep the camera in color display and B/W is on the contrary. IR SYNC makes the camera view synchronize with IR LED to switch COLOR or B/W based on the brightness of the environment. - Page 18 ■ IR OPTIMIZER: To adjust the IR Optimizer value to improve the image exposure issue when IR is turned on. The dark side of the image will also be optimized in terms of even brightness to enhance the effect as a whole. ■...
-
Page 19: Image
Image In the "IMAGE" of camera OSD, there are some items can be selected to modify the settings. The main function of this page is about the image settings. ■ SHARPNESS: To modify the value of sharpness. ■ SATURATION: To modify the value of saturation. ■... -
Page 20: Effect
Effect In the "EFFECT" of camera OSD, there are some items can be selected to modify the settings. The main function of this page is about the camera effects. ■ MOTION: To enable the "motion" effect or not. Enable this will go its sub-menu for motion setting. Please check the details in its section. -
Page 21: Motion
2.10 Motion In the "MOTION" of camera OSD, there are some items can be selected to modify the settings. The main function of this page is about the motion detection. ■ DET DISP: To enable or disable the detection display function. Please see below for advanced settings. DET DISP ON ■... - Page 22 ■ DET H-SIZE: To adjust the width (horizontal size value) of the selected area. ■ DET V-SIZE: To adjust the height (vertical size value) of the selected area. ■ SENSITIVITY: To adjust the sensitivity value for detection from 0 to 20. ■...
-
Page 23: Privacy
2.11 Privacy In the "PRIVACY" of camera OSD, there are some items can be selected to modify the settings. The main function of this page is about the privacy mask size and position. ■ ZONE NUM: To select number of zone for privacy mask from 1 to 16. ■... -
Page 24: Defog
2.12 Defog In the "DEFOG" of camera OSD, there are some items can be selected to modify the settings. The main function of this page is about the fog reduction effects. ■ MODE: To select the mode of fog reduction. ■... -
Page 25: System
2.13 System In the "SYSTEM" of camera OSD, there are several sub-menus and items can be selected to modify the settings. The main function of this page is about the video format information and OSD firmware version. ■ DIGITAL OUT: To select the digital output setting between 1080P and 720P. - Page 26 COC: To enable or disable the function of Control over Coaxial cable. ■ CABLE LENGTH: To select the Transmission Distance from 0-200M or over 200M supported by the camera with Distance Compensation Setting. ■ COLORBAR: To enable or disable the mode of COLORBAR. ■...