Advertisement
5) Debug after installation
(a)
In 20 seconds, according to the environment, the system
will automatically adjust sensing distance, please do not
put any objects in front of the sensor.
(b)
Then press the button once,the soap liquid will quickly fill
the liquid tube.
(c)
At last please put hands in the induction range,the faucet
will automatically spew soap once.
6 . USE INSTRUCTIONS
1)When putting your hand into the sensing range, the faucet
will spray soap once ,and when hands leave the sensing
range, the faucet will no longer spray soap.
2)
In order to avoid a jam in the soap tube, if no use in
48H,the faucet will automatically spray soap once.
3)
If not using for a long time,please clean the bottle
and liquid tube, detailed steps below:
(a)Pour out all soap liquid,and clean the soap bottle until
there is no foam in the bottle.
(b)Press the button once after putting some water into
bottle,the soap tube will quickly be filled.Then rinse the
tube until no foam.
(c)Press the button for more than 2 seconds to empty the
soap tube.
4)Please use the special soap of electronic induction or
foam soap,no particulate impurities or flocs,otherwise
the tube will easily be jamed and lead to product failure.
7. DAILY USE AND MAINTENANCE
1.When using for the first time or changing the soap, please
press the green button on the control housing to quick fill
the liquid soap tube.
2.When the sensor is blocked by dirt or foam,please wipe
away using a damp cloth. When cleaning around the
sensor,please be careful not to scratch the surface of the
sensor.
3. Do not directly wash the faucet body with water to avoid
accidents caused by damage to internal circuits.
4.Please clean the nozzle and the filter net when refilling the
liquid soap every time.
If the dispenser is not used for a long time or has not been
properly maintained, liquid soap remaining in the tube can
dry out and lead to spout malfunction. This is not covered
by the product warranty. Please refer to the following steps
for self-inspection and maintenance.
1.Check and clean the filter net of the bottle
Filter net
Filter cover
j a c l o i n d u s t r i e s | 129 Dermody Street Cranford, NJ 07016
p 908.653.4433 | f 908.653.1717
Gently pry the filter cover with a knife
blade, then rinse the residual impurities
or viscous soap liquid in the filter net
repeatedly with clean water.
Be careful not to break the filter net
during the cleaning process.
2.Check whether the liquid soap tube or pump tube is
blocked by viscous soap. If yes, pull out the tube joint
and squeeze out the viscous soap of the soap tube.
3.Cleaning foaming device
F ilter inlet
connector
Filter net
Filter bracket
4.Cleaning pump tube
When the pump tube is blocked or adhered,
refer to the following steps to clean the tube.
1.Please gently pull out the pump tube in
2.Remove liquid tube joint and squeeze out
3.Finally install back the joint and pull back
Pump tube
liquid tube
joint
8. TROUBLE SHOOTING
Check the following before contacting the service center.
1. Soap does not flow when hands are placed within the
sensing range.
CAUSE
a) Suspension of power supply
b) Soap used up
c) Liquid outlet blockage
d) There are foreign objects in the
induction range
e) Filter net in the bottle blockage -Cleaning filter net
f) Liquid tube is bent
2. Soap liquid flow is not smooth
CAUSE
a) Soap is too thick
b) Liquid outlet blockage
c) Filter net in the bottle blockage -Cleaning filter net
This device is hidden at the bottom of
the faucet body.
Please be careful not to scratch the
strainer of the filter net during cleaning.
When installing back the foam device, be
careful not to forget to install o-ring.
the direction of the arrow on the picture.
the thick soap.
the pump tube in the opposite direction.
CHECKPOINT
-Switch on the power
-Add soap liquid
-Cleaning liquid outlet
-Remove foreign objects
-Straighten the liquid tube
CHECKPOINT
-Use the special soap of
electronic induction
-Cleaning liquid outlet
JACLO.COM
12/2/20
| PG 3
Advertisement
