Excel Dryer XLERATORsync Installation And Owner's Manual

Advertisement

R E A D A N D S AV E T H E S E I N S T R U C T I O N S
1.
Unpack all items from the shipping box.
2.
Review items against the following list:
1. Dryer Box Assembly
2. Deck Up Spout Assembly
3. Hose Assembly
4. Z-Bracket
5. Installation and Owner's Manual
3.
Report any missing or damaged items.
4.
Locate the Dryer Model Number and Serial Number
on the Dryer nameplate and record the date below.
5.
Read and save these instructions.
Serial Number
Date Of Purchase
WARNING: For proper electrical connections,
check your local building codes. Dryer is
intended to be cord connected to power supply,
and must be properly grounded.
WARNING: To reduce risk of fire, electric shock
or injury to persons, observe the following:
A Use this unit only in the manner intended by the
manufacturer.
B Before servicing or cleaning unit, unplug cord
from receptacle.
GENERAL SAFETY INSTRUCTIONS
If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a
hazard.
To preserve IP11B rating, dryer must be connected to air delivery hose
and connector
Troubleshooting and internal maintenance must be performed by
qualified service personnel.
E X C E L D R Y E R , I N C
A D M I N @ E X C E L D R Y E R . C O M
INSTALLATION AND OWNER'S MANUAL
RECEIVING SHIPMENT
MODEL INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
1 . 4 1 3 . 5 2 5 . 4 5 3 1
1 . 8 0 0 . 2 5 5 . 9 2 3 5 ( U S / C N )
3 5 7 C H E S T N U T S T R E E T, E A S T L O N G M E A D O W , M A 0 1 0 2 8
XLERATORsync
This appliance is designed to be used in commercial areas.
1
2
4
Do not use any power wash equipment for cleaning on or near this
unit.
Do not use the XLERATORsync dryer for drying hair.
Do not obstruct air inlets or outlets.
PRE INSTALLATION WIRING SAFETY INSTRUCTIONS
Install a dedicated 20-amp GFCI outlet no more than 4 feet from
the installation of the dryer box. Make sure the supply corresponds
to that shown on the rating sticker of the unit. If the dryer is
connected to any electrical supply other than that stated on the
rating sticker of the unit, permanent damage or improper, unsafe
operation of the unit may result.
Make sure to unplug cord from receptacle before installing,
maintaining or cleaning this hand dryer.
E X C E L D R Y E R . C O M
®
3
5
5 / 2 0 2 0
1
EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XLERATORsync and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Excel Dryer XLERATORsync

  • Page 1 Dryer is unit. intended to be cord connected to power supply, • Do not use the XLERATORsync dryer for drying hair. and must be properly grounded. • Do not obstruct air inlets or outlets. WARNING: To reduce risk of fire, electric shock...
  • Page 2: Installation Instructions

    R E A D A N D S AV E T H E S E I N S T R U C T I O N S INSTALLATION INSTRUCTIONS CAUTION: Always make sure to have dryer electrical cord unplugged from outlet before performing any installation or maintenance tasks. 1.
  • Page 3 R E A D A N D S AV E T H E S E I N S T R U C T I O N S 3. If not already installed attach supplied Z Bracket to sink base per instructions from wash station manufacturer.
  • Page 4 R E A D A N D S AV E T H E S E I N S T R U C T I O N S 5. Similar to step 4, align the slots on the hose connector with the dryer output tabs. Insert Hose Connector until it stops, then rotate clockwise about 1/8th of a turn to snap into place in Twist hose...
  • Page 5: Cleaning & Maintenance

    R E A D A N D S AV E T H E S E I N S T R U C T I O N S R E A D A N D S AV E T H E S E I N S T R U C T I O N S WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A.
  • Page 6: Code Chart

    R E A D A N D S AV E T H E S E I N S T R U C T I O N S CODE CHART Codes are displayed by the flashing of the red LED light in the sensor behind air outlet and on the front of the dryer box under the sink. Normal operation will be indicated by the red LED being on when not drying and off when hands are under the sensor.

Table of Contents