ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Installation:
1. Open the hood and remove the protective cover from the front of the engine compartment (Fig. 1). Refer to the vehicle owner's manual.
Fig. 2
Fig. 2
Fig. 2
Existing
Rivnut
three supplied 1/4 - 20 X 1" Hex Head Cap Screws and Internal Tooth Lockwashers.
7. Extend the WHITE (positive) and BLACK (negative) speaker wires to your siren amplifier and
connect as shown in the amplifiers instructions. Test the siren to confirm proper operation.
8. Reinstall the protective cover to complete this installation. Test all vehicle components and equipment before returning the vehicle to service.
©2007 Whelen Engineering Company Inc.
Form No.14117C (070909)
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Installation:
1. Open the hood and remove the protective cover from the front of the engine compartment (Fig. 1). Refer to the vehicle owner's manual.
Fig. 2
Fig. 2
Fig. 2
Existing
Rivnut
three supplied 1/4 - 20 X 1" Hex Head Cap Screws and Internal Tooth Lockwashers.
7. Extend the WHITE (positive) and BLACK (negative) speaker wires to your siren amplifier and
connect as shown in the amplifiers instructions. Test the siren to confirm proper operation.
8. Reinstall the protective cover to complete this installation. Test all vehicle components and equipment before returning the vehicle to service.
©2007 Whelen Engineering Company Inc.
Form No.14117C (070909)
®
3. With the bracket in its exact mounting location, mark off
the 2 bolt locations where you will install riv nuts then
remove the bracket.
4. Drill the 2 mounting holes (and widen the existing hole)
using a .391" drill bit and install the three Rivnuts.
5. Secure the siren speaker to the bracket with the supplied
hardware (Fig. 3). IMPORTANT: Refer to next page for
more information on mounting speaker to bracket.
6. Secure the bracket (with speaker) to the vehicle using the
For warranty information regarding this product, visit www.whelen.com/warranty
®
3. With the bracket in its exact mounting location, mark off
the 2 bolt locations where you will install riv nuts then
remove the bracket.
4. Drill the 2 mounting holes (and widen the existing hole)
using a .391" drill bit and install the three Rivnuts.
5. Secure the siren speaker to the bracket with the supplied
hardware (Fig. 3). IMPORTANT: Refer to next page for
more information on mounting speaker to bracket.
6. Secure the bracket (with speaker) to the vehicle using the
Page 1
For warranty information regarding this product, visit www.whelen.com/warranty
SA315 Siren Speaker Bracket
2007-2009 Suburban/Tahoe
Internet: www.whelen.com
Sales e-mail: autosale@whelen.com
Customer Service e-mail: custserv@whelen.com
2. Remove the existing bolt (Fig. 2) from the passenger side radiator
support and use it to secure the bracket to the vehicle.
IMPORTANT NOTE! This installation uses Rivnuts™ to secure the
bracket to the vehicle. This type of hardware requires the use of a
specialized installation tool. Refer to the owners manual included
with this tool for proper installation. Be sure to follow the mounting
hole specifications precisely!
1/4" SPLIT
LOCKWASHER
SA315 Siren Speaker Bracket
2007-2009 Suburban/Tahoe
Internet: www.whelen.com
Sales e-mail: autosale@whelen.com
Customer Service e-mail: custserv@whelen.com
2. Remove the existing bolt (Fig. 2) from the passenger side radiator
support and use it to secure the bracket to the vehicle.
IMPORTANT NOTE! This installation uses Rivnuts™ to secure the
bracket to the vehicle. This type of hardware requires the use of a
specialized installation tool. Refer to the owners manual included
with this tool for proper installation. Be sure to follow the mounting
hole specifications precisely!
1/4" SPLIT
LOCKWASHER
Installation Guide:
1/4" SPLIT
LOCKWASHER
1/4 - 20 X 1-1/2"
HEX HEAD BOLT
1/4 - 20 X 1-1/4"
Fig. 3
HEX HEAD BOLT
Installation Guide:
1/4" SPLIT
LOCKWASHER
1/4 - 20 X 1-1/2"
HEX HEAD BOLT
1/4 - 20 X 1-1/4"
Fig. 3
HEX HEAD BOLT
Need help?
Do you have a question about the SA315 and is the answer not in the manual?
Questions and answers