Advertisement
Quick Links
Advertisement
Summary of Contents for Dahl VARIODOCK
- Page 1 DAHL VARIODOCK™ Maintenance Manual Installation and User Guide 503749 · 01.2021...
- Page 2 12. It is forbidden to combine Dahl WTORS components with those of other manu- and becomes the responsible manufacturer of the customized device.
- Page 3 The contents of a standard kit with Dahl VarioDock, art. no. 503600, are shown on the appliance concerned. We are therefore continuing our efforts to next page.
- Page 4 All steel wires must be examined for signs of wear or evidence of breaks. Replace if necessary. When the maintenance light is activated, VarioDock must undergo maintenance within 200 uses. Order service kit with art. no. 503636 (see also pages 34-35).
- Page 5 All steel wires must be examined for signs of wear or evidence of breaks. Replace if necessary. When the maintenance light is activated, VarioDock must undergo maintenance within 200 uses. Order service kit with art. no. 503636 (see also pages 34-35).
- Page 6 All steel wires must be examined for signs of wear or evidence of breaks. Replace if necessary. When the maintenance light is activated, VarioDock must undergo maintenance within 200 uses. Order service kit with art. no. 503636 (see also pages 34-35).
- Page 7 , seat belts and components should be When the maintenance light is activated, VarioDock must undergo maintenance within 200 uses. Order service kit with art. no. 503636 (see also pages 34-35). locking plate touches the locking pin, a warning tone 1.
- Page 8 VarioDock, the wheelchair is guided into place by means of Lamp illuminates when maintenance the lock plate. is due. When the lock plate is fully engaged in the VarioDock, a Yellow button: Adjusts upwards. Keep spring-loaded lock pin (3) automatically secures the lock button pressed, to increase step length, plate.
- Page 9 B. Loosen the 4 bolts on the side of the VarioDock the wheelchair may not be manoeuvred properly into chair components may be damaged.
- Page 10 6 mm plywood Plywood Plywood spacers #503660 spacers #503660 Plywood spacers Reinforcing brackets Use a hammer to make a dent for the nut if placed on top of floor pan Maintenance manual, installation and user guide UK Dahl VarioDock™...
- Page 11 Tightening torques 1. Art.no. 503125 – Dahl lock plate and 8mm spacer, 2. Art.no. 502685 and 502735, 3. Art.no. 502839 with Dahl Special Bolts #502800 bolts inside the VarioDock – bolts on the side of the VarioDock WARNING! In countries where legislation demands meeting EU-Regu lation...
- Page 12 Display is permanently active If the docking station is used by a person driving the vehicle himself If VarioDock is to be used for multiple wheelchairs, we recommend choosing a low – At an easily accessible and visible location when the wheelchair is tightening rate to avoid any damage to the wheelchairs due to excessive pulling.
- Page 13 Note 1: Terminal Block 12 Volt DC documentation. Note 2: Electrical Plug You can find videos and more information about maintenance and installation of DAHL Vario- Dock on our website: http://wtors.com Maintenance manual, installation and user guide UK Dahl VarioDock™...
- Page 14 Always make sure that the vehicle floor is approved for use of seats with integrated Do not use VarioDock™ to anchor Dahl COMFORT Seats or other seats with integrated seat belt anchor points, if the vehicle has not been fitted with an 3-point seat belt.
- Page 15 Recommended location of Clear zones are recommended areas in which hard or sharp installation components or objects Only use Dahl WTORS or e-(ECE), E-(EU) or ISO 10542 certified safety shoulder belt’s top anchoring point: should not be placed. The clear zone recommendations in ISO 10542 are based on the way in belts for securing occupants of the vehicle.
- Page 16 Driving direction will be used in, for fitting the docking system and safety belts for the wheelchair The following fitting examples for fitting the Dahl VarioDock can only be used in user. countries where no legal requirements to tests of docking system in the specific Please enquire with regard to the current range of vehicle specific fitting kits with vehicle and mounting position are to be found.
- Page 17 Safety belt buckle can be orde- the vehicle floor. whether this is a 3-point belt, an H- or lap belt. red in different lengths. Please ask about the current range. Maintenance manual, installation and user guide UK Dahl VarioDock™...
- Page 18 Spare parts list for VarioDock Quantity Art. no. Description #503600 503502C Top plate 503125 Lock plate, complete 503555 Lock pin, complete 502358 Top cover, complete 502357 Motor, complete 503554 Potentiometer, complete 503519C Cable for quick release 502350C Solenoid/Electromagnet 503553C Control panel...
- Page 19 WHERE SAFETY STARTS Development and crash-test centre Where safety starts Dahl Engineering ApS Løvevej 3 DK-7700 Thisted Danmark Telefon: +45 9618 0077 sales@dahlengineering.dk w: wtors.com...
Need help?
Do you have a question about the VARIODOCK and is the answer not in the manual?
Questions and answers