Subscribe to Our Youtube Channel
Summary of Contents for REMKO HITLINE LRM Series
- Page 1 Operating and installation instructions REMKO LRM series Air purifier LRM 350, LRM 500 0276-2020-11 Edition 1, en_GB Read the instructions prior to performing any task!
- Page 2 Read these operating instructions carefully before commis- sioning / using this device! These instructions are an integral part of the system and must always be kept near or on the device. Subject to modifications; No liability accepted for errors or mis- prints! Translation of the original...
-
Page 3: Table Of Contents
Table of contents Safety and usage instructions......................4 1.1 General safety notes........................4 1.2 Identification of notes........................4 1.3 Personnel qualifications........................4 1.4 Dangers of failure to observe the safety notes................4 1.5 Safety-conscious working....................... 4 1.6 Safety instructions for the operator....................5 1.7 Safety notes for installation, maintenance and inspection work............ -
Page 4: Safety And Usage Instructions
REMKO LRM series Safety and usage instructions CAUTION! This combination of symbol and signal word 1.1 General safety notes warns of a potentially hazardous situation, which if not avoided may cause injury or mate- Carefully read the operating manual before com- rial and environmental damage. -
Page 5: Safety Instructions For The Operator
1.6 Safety instructions for the 1.7 Safety notes for operator installation, maintenance and inspection work The operational safety of the units and compo- nents is only assured providing they are used as Appropriate hazard prevention measures must intended and in a fully assembled state. be taken to prevent risks to people when per- forming installation, repair, maintenance or This unit can be used by children above the age of... -
Page 6: Intended Use
"certificate of warranty" to components (for example batteries) are not dis- REMKO GmbH & Co. KG at the time when the posed in household waste, but only in accordance units are purchased and commissioned. -
Page 7: Technical Data
Technical data 2.1 Unit data Unit data LRM 350 Series LRM 350 Version Local air purifier with quadruple filtration Max. cleaning performance Nylon pre-filter, filter foam mat, activated carbon Filter stages granulate cassette, HEPA H13 filter HEPA H13 filter separation efficiency 99.975 Operating range °C/r.H.%... - Page 8 REMKO LRM series Unit data LRM 500 Series LRM 500 Version Local air purifier with quadruple filtration Max. cleaning performance Nylon pre-filter, filter foam mat, activated carbon Filter stages granulate cassette, HEPA H13 filter HEPA H13 filter separation efficiency 99.975 Operating range °C/r.H.%...
-
Page 9: Unit Dimensions
2.2 Unit dimensions LRM 350 Fig. 1: Unit dimensions LRM 350 (all measurements in mm) LRM 500 Fig. 2: Unit dimensions LRM 500 (all measurements in mm) We reserve the right to modify the dimensions and design as part of the ongoing technical development process. -
Page 10: Design And Function
The use of REMKO air purifiers Our ambient air contains a lot of different foreign substances such as dust, fibres, pollen, germs and... -
Page 11: Unit Description
Diffusion effect Very small particles (<1µm) are guided by Brow- 3.2 Unit description nian molecular motion. The particles do not follow the general air flow, but move completely at The units have been designed for universal and random in a zigzag pattern and eventually hit a straightforward air purification. - Page 12 REMKO LRM series Unit construction The basis is a flow-optimised housing with a centrally positioned radial fan. The room air is sucked in over a large area at the rear of the unit and drawn through the filters arranged in a row. The cleaned air is then fed back into the room via the air outlet on the top of the unit.
-
Page 13: Operation
Operation Fig. 9: Control panel "ON/OFF" key “Anion” generator key This key switches the unit on and off. This key can be used to activate and deactivate the anion generator. When the anion generator is “Fan Speed” key activated, the air purifier produces anions that attract and bind suspended particles in the air. -
Page 14: Assembly
REMKO LRM series Assembly “Filter” filter change key This key can be used to reset the filter cleaning or 5.1 Unit transport filter change message after filter cleaning or filter change has been completed. If filter cleaning or a The units can be transported either upright or lying filter change is necessary, the corresponding LED down. -
Page 15: Setting Up The Unit
5.2 Setting up the unit The air purifier should be placed as centrally as possible in the middle of the room to achieve For the best economic and safe use of the units, optimum air circulation the following notes must be followed in full: The units must be set up in an upright and level position in order to ensure unhindered operation of the unit... -
Page 16: Commissioning
REMKO LRM series Commissioning Shutdown Initial commissioning If the air purifier is to be deactivated, this can be done either manually using the “ON/OFF” key on The air filters are shrink-wrapped in film when the operating panel or automatically using the pre- delivered. -
Page 17: Care And Maintenance
Care and maintenance Filter maintenance intervals There are 4 LEDs on the operating element, each assigned to a filter stage. The individual LEDs light up after a defined operating time has elapsed and thus indicate the required filter cleaning or filter change. The prompt is displayed sooner or later, depending on user behaviour. - Page 18 REMKO LRM series Pull the nylon pre-filter out of the unit by the Pull the granular activated carbon cartridge tabs. Pay attention to the retaining tabs on out of the unit by the tab. the sides and on the lower edge Pull the HEPA filter out of the unit by the tab.
- Page 19 Cleaning the pre-filter Replacing the after-filters The pre-filter consists of a nylon fabric that pre- The filter foam mat, the activated carbon granulate vents coarse particles such as hair and dust flakes cassette and the HEPA filter cannot be regener- from further entering the following filters.
-
Page 20: Troubleshooting And Customer Service
REMKO LRM series Troubleshooting and customer service The unit and components are manufactured using state-of-the-art production methods and tested several times to verify that they function correctly. However, if malfunctions should occur, please check the functions as detailed in the list below. For systems with an indoor unit and outdoor unit, refer to the chapter "Trouble- shooting and customer service"... -
Page 21: View Of The Unit
View of the unit Fig. 18: Exploded view LRM 350, LRM 500... -
Page 22: Spare Parts List
REMKO LRM series Spare parts list Designation LRM 350 LRM 500 Operating panel film Housing front Operating board Fan motor Control board Maintenance flap air quality sensor Housing side, left Housing top section Air outlet finned grille Air quality sensor... -
Page 23: Index
Index General ......4 Identification of notes ....4 Care and maintenance . - Page 24 REMKO QUALITY WITH SYSTEMS Air-Conditioning | Heating | New Energies Telephone +49 (0) 5232 606-0 REMKO GmbH & Co. KG Hotline within Germany +49 (0) 5232 606-0 Klima- und Wärmetechnik Telefax +49 (0) 5232 606-260 Im Seelenkamp 12 E-mail info@remko.de...
Need help?
Do you have a question about the HITLINE LRM Series and is the answer not in the manual?
Questions and answers