Related Manuals for Samsung SH-S222A
Summary of Contents for Samsung SH-S222A
- Page 1 Select Langu Samsung's OMS (Optical Media Solution) Customer Support Website English (http://www.samsung-ODD.com) offers the latest versions of firmware for ODD products, user instructions and product information.
- Page 2 RoHS & WEEE Installing DVD Writer and Connecting Cables Installing Drive Connecting Cables How To Use The DVD Writer How to Use the Drive How to Use DVD±R/RW and Other Discs MAGIC SPEED Deleting Utilities Troubleshooting Troubleshooting Caution: Possible Errors Product Specifications...
- Page 3 Do not disassemble Always make sure that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended to make a copy immediately and use the copy instead.
- Page 4 Select Languages English Do not drop the drive, and protect it from severe shocks. - It can damage the drive or cause it to malfunction. Do not place the drive in direct sunlight. Avoid low-or high-temperature environments. Avoid high-humidity environments.
- Page 5 Always check to be sure the disc is not cracked before use. If you find a crack on the disc (especially around the center hole), make a copy of the disc immediately and use the copy instead.
- Page 6 Never allow food particles or foreign substances to enter the drive casing. To protect against the risk of fire, do not spill such liquids as alcohol and benzene on the drive. Do not disassemble, attempt to repair or modify the device without an express approval as directed in the manual.
- Page 7 This mark shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from a uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
- Page 8 3. Master/Slave Selection Port • This product is not quipped with an audio output port. However, audio output is supported using the E-IDE data cable on the default digital audio program provided by the operating system. DVD Writer Four screws to install the drive Setup guide Application software &...
- Page 9 In case you need to return the purchased product, be sure to include all the accessories provided with the product to receive a refund. The type of accessories varies depending on a product model. and some accessories described herein are subject to change without notice.
- Page 10 Select Languages English Item Description Microsoft Windows 2000/XP/Vista Pentium4 2.0GHz or above 512MB or above(Windows 2000, XP), 1GB or above(Windows Vista)
- Page 11 Writable : write once, read many times. Rewritable : write data one or more times. DVD Recommended Disc Types DVD-R Media Taiyo-Yuden, TDK, MKM, Hitachi, Maxell, FujiFilm, PVC, Panasonic, RiTEK, CMC, UNIFINO DVD-RW Media TDK, MKM, JVC, PVC, RiTEK, CMC DVD+R Media...
- Page 12 DVD+RW(12X), CD-ROM (48X), CD-R (40X), CD-RW (40X), DVD+R DUAL(12X), DVD-R DUAL (12X), DVD-RAM(12X) Recording Speed(MAX) DVD+R DUAL (16X), DVD+RW (8X), DVD-R(22X), DVD+R(22X), DVD-RW (6X), CD-R (48X), CD-RW (32X), DVD-R DUAL (12X), DVD-RAM(12X) ( The maximum speed depends on the writing media condition or some of user`s PC environment. )
- Page 13 1. Turn the PC off. 2. Open the cover as shown in the picture. 3. If necessary, attach the support devices on both sides of the drive - The support devices are PC accessories. Purchase a pair if necessary. (SCREW : M3 X 6 X 4 ) 4.
- Page 14 Connecting the Power Cable Hold the power cable (with four pins) in the power box within the computer with the cutoff edges( facing up and connect it to the power port in the back of the DVD Writer A - Cutoff edges Improperly connected power cable may cause malfunction.
- Page 15 : Master Drive (Select the MA jumper) c : MainBoard e : Secondary 1 When you have one DVD Writer and the other ODD products: Set it to MA (Master) / SL (Slave), b : HDD d : Primary 1...
- Page 16 Connect the jumper to the slot in the back of the DVD Writer. When you connect the jumper to MA (Master), the drive runs as the master, and when you connect it to SL (Slave), the drive runs as the slave.
- Page 17 Select Languages English 1. Go to http://www.samsung-ODD.com 2. Click Firmware on the menu bar (in the upper right-hand corner). 3. Click Firmware Downloads. Check for your drive model and start downloading.
- Page 18 3. Click DVD-W drive in the Device Manager window. ① in the left picture appears if the driver is installed properly. 1. Go to [Start] - [Settings] - [Control Panel] - [Performance and Maintenance] 2. Click [Administrative Tools] icon in the Performance and Maintenance window.
- Page 19 When the LED is Green, do not turn the PC off or remove the DVD Writer as it may cause damage in the drive. How to Use a Horizontally Installed Drive You can use 3.15 Inch or 4.72 Inch (8cm or 12cm) disc.
- Page 20 The DVD Writer supports RPC phase II. In the RPC-2 mode, the local code can be changed by users. RPC-2 is selected by default for The DVD Writer.
- Page 21 ● Silent Mode: Setting reading speed to a stable low speed. ● Any mode set by Magic Speed will be reset to "Low nosie mode" when the PC restarts, so please check the current mode if you want to use “The maximum speed mode” and change the settings where necessary.
- Page 22 Click [Start] - [Setting] - [Control Panel] - [Add/Remove Programs] and a window as shown below appears. [ Windows 2000 ] [ Windows XP ] Select Languages English Click the [Add/Remove] button to remove the program. Click the [Add/Remove] button to remove the program.
- Page 23 Turn the PC off and pull out the drive. Remove any foreign objects from the surface of the drive using soft cloth. - Do not use benzene, paint thinner, or any other solvents. - Cleaning the interior of the unit with such things as a cotton swab may cause a failure or a loss of function.
- Page 24 Read carefully and use the device properly. Do not place it under the direct sunlight. Place it so that it sits on its side on a flat surface. Do not scratch or place a label on the disc. Handle the disc with caution to prevent damage from an external shock.
- Page 25 Clean the disc lightly with soft cotton cloth, starting from the center and move to the edge of the disc. Use only disc-cleaning liquids. Do not use benzene, paint thinner, or any other solvents. If the disc surface becomes dirty with fingerprints, foreign substances or dust, the disc may not function properly. Select Languages...
- Page 26 Green: Blinks every 0.3 seconds. Disc Lead-In Green: Blinks every 0.3 seconds. Writing Reading Green: Blinks every 0.3 seconds. Standby No Disc The indicator light turns off when the drive is not in use (standby) after disc lead-in. Select Languages English Meaning...
- Page 27 See if the drive is properly connected to the PC. See if the floppy disc remains in the PC. The drive is not working properly. See if the drive is connected properly to the PC. See if the device drive program has been installed properly.
- Page 28 DVD Writers record data on the disc by applying laser light onto the surface of the disc, and therefore writing errors may occur if you use a damaged disc, for example. Be sure to eliminate the following error-causing elements before you start writing: * The following settings are recommended for all DVD Writer: Avoid a situation that requires multitasking, and remove turn off the screen saver.
- Page 29 You may experience lower write quality in case if you use disc products by some disc makers which that are not registered with the product's firmware. Therefore, it is recommended that you use only discs by recommended companies. Even, and even if the write session is completed successfully, check the write quality before you put the disc in storage, especially in case of an important data backup.
- Page 30 Specifications are subject to change without notice. FCC information to the user This equipment has been tested and found to comply with the limits for a class B digital device. pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 31 Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio TV technician for help.